Lincoln Electric IM544-B manual Amphenol 14 PIN

Page 37

COMMANDER 400 STICK & WIRE / LN-25 ACROSS THE ARC CONNECTION DIAGRAM WITH OPTIONAL K857 REMOTE CONTROL

WARNING
Do not operate with panels open.	Keep guards in place.
Disconnect NEGATIVE (-) BATTERY LEAD	Keep away from moving parts.
before servicing.	Only qualified personnel should install,use
Do not touch electrically live parts.	or service this equipment.

CONNECTION	F-5
DIAGRAM:

COMMANDER 400

AMPHENOL 14 PIN

TO WORK

ELECTRODE

6 PIN				OPTIONAL K857
AMPHENOL				REMOTE CONTROL
AMPHENOL				REMOTE CONTROL

LN-25

WIRE FEEDER

WORK CLIP LEAD

TO WORK

TO WORK

ELECTRODE CABLE

DIAGRAMS

N.A. WELDING CABLE MUST BE OF PROPER CAPACITY FOR THE CURRENT AND DUTY CYCLE OF IMMEDIATE AND FUTURE APPLICATIONS. SEE OPERATING MANUAL.

N.B. USE VOLTMETER SWITCH TO SELECT DESIRED ELECTRODE POLARITY.

N.C. IF REMOTE OUTPUT CONTROL IS USED, PLACE LOCAL/REMOTE SWITCH IN "REMOTE" POSITION.

N.D. ON COMMANDER 400 STICK & WIRE, THE OUTPUT CONTROL SWITCH MUST BE IN THE "WELDING

TERMINALS ALWAYS ON" POSITION .

12-13-96

S22912

F-5

Image 37

Contents Safety Depends on You CommanderCalifornia Proposition 65 Warnings SafetyElectric Shock can kill Iii Welding Sparks can cause fire or explosionSûreté Pour Soudage a L’Arc Précautions DE SûretéThank You Table of Contents Welding Range Open Circuit Voltage Auxiliary Power1 InstallationHEIGHT2 Width Depth Weight Bore x StrokeLOCATION/VENTILATION Safety PrecautionsStacking Angle of OperationHigh Altitude Operation PRE-OPERATION Engine ServiceTowing OILElectrical Output Connections Engine Cooling System Battery ConnectionFuel CAP Muffler Outlet PipeStandby Power Connections Auxiliary Power ReceptaclesWelding Output Cables Machine GroundingPower Operation Safety InstructionsOperating Instructions General DescriptionFor Auxiliary Power Additional Design FeaturesOther Features For Wire WeldingRUN- Stop Switch Controls and SettingsStart Pushbutton Idler Switch Engine Temperature Gauge and LightEngine Alternator Ammeter and Light Idler Operational exceptionsAuxiliary Power Controls Engine Operation Wire Feeder Mode ControlsStarting the Engine Stopping the EngineTypical Fuel Consumption Welder OperationStick Welding TIG WeldingCommander 400 Settings When Using the K930-1 TIG Module Commander 400 Settings When Using the K799 HI-FREQ UnitTable B.3 Typical Current Ranges 1 for Tungsten ELECTRODES2 Stick and Wire Model Connection to LN-25 Wire Feed Constant Voltage WELD- INGStick and Wire Model Connection to LN-23P Stick and Wire Model Connection to NA-3Simultaneous Welding and AUXIL- Iary Power Loads Auxiliary Power OperationOptional Field Installed Accessories AccessoriesRecommended Equipment Routine and Periodic Maintenance MaintenanceEngine Maintenance Fuel PRE-FILTER/WATER Separator ASSEM- BLY Fuel FiltersWater Separator Element Cooling System Cooling Blower Belt Battery HandlingMake Part Number HOW to USE Troubleshooting Guide TroubleshootingPossible Areas SymptomsCourse of Action Function Problems Output Problems Diagrams Commander K488 / K487 Spool GUN Connection Diagram DiagramsCommander 400 Stick & Wire / LN-23P Connection Diagram DiagramAmphenol 14 PIN Commander 400 Stick & Wire / K867 / LN-8 Connection Diagram Electrode Cable To Wire Feed Unit LN-7 Connection Diagram Electrode Cable Commander 400 Stick & Wire / LN-8 Connection Diagram Dimension Print Commander $700.00 Basic CoursePrecaucion Aviso DE Warranty Period 1 2 Statement of Limited WarrantyConditions of Warranty Warranty Limitations