Lincoln Electric IM826-A manual Auxiliary Power Operation

Page 25

B-8

OPERATION

B-8

CV-WIRE MODE

Connect a wire feeder to the AIR VANTAGE® 500 and set welder controls according to the instructions listed earlier in this section.

The AIR VANTAGE® 500 in the ”CV-WIRE” position, permits it to be used with a broad range of flux cored wire (Innershield and Outershield) electrodes and solid wires for MIG welding (gas metal arc welding). Welding can be finely tuned using the “ARC CONTROL”. Turning the ARC CONTROL clockwise from - 10(soft) to +10(crisp) changes the arc from soft and washed-in to crisp and narrow. It acts as an inductance/pinch control. The proper setting depends on the procedure and operator preference. Start with the knob set at 0.

For any electrodes, including the above recommendations, the procedures should be kept within the rating of the machine. For additional electrode information, See www.lincolnelectric.com or the appropriate Lincoln publication.

ARC GOUGING

For optimal performance when arc gouging, set the AIR VANTAGE® 500 “WELD MODE” switch to the “CC - STICK” position, and the “ARC CONTROL” to 10.

Set the “OUTPUT” knob to adjust output current to the desired level for the gouging electrode being used according to the ratings in the following table:

 

ELECTRODE

CURRENT RANGE

 

DIAMETER

(DC, electrode positive)

 

(1/8”)

30-60 Amps

 

(5/32”)

90-150 Amps

 

(3/16”)

200-250 Amps

 

(1/4”)

300-400 Amps

 

(5/16”)

350-450 Amps

 

(3/8”)

450-575 Amps*

 

 

 

NOTE: If desired the CV mode can be used for Arc Gouging.

*Maximum current setting is limited to the AIR VANTAGE® 500 maximum of 575 Amps.

PARALLELING

When paralleling machines in order to combine their outputs, all units must be operated in the CC-STICK mode only at the same output settings. To achieve this, turn the WELD MODE switch to the CC-STICK position. Operation in other modes may produce erratic outputs, and large output imbalances between the units.

AUXILIARY POWER OPERATION

If a GFCI receptacle is tripped, See the MAINTENANCE section for detailed information on testing and resetting the GFCI receptacle.

Start the engine and set the IDLER control switch to the desired operating mode. Full power is available regardless of the welding control settings, if no welding current is being drawn.

The auxiliary power of the AIR VANTAGE® 500 consists of two 20 Amp-120VAC single phase (5-20R) GFCI duplex receptacles, one 50 Amp-120/240VAC single phase (14-50R) receptacle and one 50 Amp 240VAC three phase (15-50R) receptacle. The 120/240VAC receptacle can be split for single phase 120 VAC operation.

The auxiliary power capacity is 12,000 watts of 60 Hz, single phase power or 20,000 watts of 60Hz, three phase power. The auxiliary power capacity rating in watts is equivalent to volt- amperes at unity power factor. The maximum permissible current of the 240 VAC output is 50 A. The 240 VAC single phase output can be split to provide two separate 120 VAC outputs with a maximum permissible current of 50 A per output to two separate 120 VAC branch circuits. Output voltage is within ± 10% at all loads up to rated capacity.

NOTE: The two 120V GFCI receptacles and the two 120V circuits of the 120/240V receptacle are connected to different phases and cannot be paralleled.

The auxiliary power receptacles should only be used with three wire grounded type plugs or approved double insulated tools with two wire plugs.

The current rating of any plug used with the system must be at least equal to the current capacity of the associated receptacle.

SIMULTANEOUS WELDING AND AUXILIARY POWER LOADS

It must be noted that the above auxiliary power ratings are with no welding load.

Simultaneous welding and power loads are specified in table B.4. The permissible currents shown assume that current is being drawn from either the 120 VAC or 240 VAC supply (not both at the same time).

AIR VANTAGE® 500 CUMMINS

Page 24 Page 26
Image 25
Page 24 Page 26
Contents AIR Vantage 500 Cummins California Proposition 65 Warnings SafetyElectric Shock can kill Welding and Cutting Sparks can Cause fire or explosion Sûreté Pour Soudage a L’Arc Précautions DE SûretéCustomer Assistance Policy Thank YouTable of Contents Vii Technical Specifications AIR Vantage 500 Cummins K2325-1 InstallationAIR Vantage 500 Cummins Location / Ventilation Safety PrecautionsStoring StackingLifting High Temperature OperationHigh Altitude Operation TowingPRE-OPERATION Engine and Compressor Service Welding Terminals Auxiliary Power Receptacles Remote ControlStandby Power Connections OutputCompany Connection of LN-7, LN-8 or LN-742 to AIR Vantage Connection of Lincoln Electric Wire FeedersConnection of LN-15 to the AIR Vantage Terminals on Connection of the LN-25 to the AIR VantageOperation Safety InstructionsGeneral Description 2OPERATIONB-2 Controls and SettingsIdler Switch Battery Charging LightOIL Pressure Gauge Engine ProtectionAuxiliary Power Controls Engine Operation Welder Operation BREAK-IN PeriodFor Tungsten Electrodes AIR Vantage 500 Settings When Using K930-2 TIG ModuleAuxiliary Power Operation Plus Weld Phase Both 1 and 3 Phase Amps WattsOptional Field Installed Accessories AccessoriesTIG Options K2641-2 Four Wheeled Steerable Yard TrailerRoutine and Periodic Maintenance MaintenanceEngine Maintenance 2MAINTENANCED-2 Service Instructions & Installation TipsFuel Filters Battery HandlingCooling System Welder / Generator Maintenance HOW to USE Troubleshooting Guide TroubleshootingRecommended SymptomsCourse of Action Function Problems Troubleshooting Diagrams Connection Diagram AIR Vantage 500 Cummins 2DIAGRAMSF-2Commander / K867 / K775 / LN-7 Connection Diagram 4DIAGRAMSF-4 5DIAGRAMSF-5 Cummins Connection Diagram7DIAGRAMSF-7 8DIAGRAMSF-8 9DIAGRAMSF-9 10DIAGRAMSF-10 11DIAGRAMSF-11 12DIAGRAMSF-12 M18962-4 Dimension PrintMojada GroundNe laissez ni la peau ni des Inflammable Votre corpsGuards off Keep your head out of fumesRespiración Alimentación de poder de la Guardas quitadas Humos. Utilice ventilación o Servicio Aspiración para gases

IM826-A specifications

The Lincoln Electric IM826-A is a state-of-the-art multi-process welder designed to meet the needs of professional welders in various industrial applications. Known for its advanced technology and robust performance, the IM826-A stands out as a reliable tool in the welding industry.

One of the main features of the IM826-A is its multi-process ability, allowing operators to seamlessly switch between MIG, TIG, and stick welding. This versatility makes the welder suitable for a wide range of materials, including steel, stainless steel, and aluminum, which is crucial for fabricators and manufacturers working with different types of metals. The ability to handle multiple processes in one machine minimizes the need for additional equipment, ultimately saving time and costs.

The IM826-A incorporates Lincoln Electric's proprietary inverter technology, which enhances its energy efficiency while providing consistent and stable arc performance. This technology allows for a lightweight design without compromising on power, making the welder more portable and easier to maneuver. It also helps in reducing energy consumption, which is a significant advantage for businesses focused on sustainability.

Another noteworthy characteristic of the IM826-A is its advanced control system. Featuring a digital display interface, users can easily adjust settings to achieve the desired welding parameters. This level of control enhances precision and accuracy in welding applications, ensuring high-quality results every time. Additionally, the IM826-A is equipped with a variety of built-in safety features, including thermal overload protection, which safeguards the machine from overheating during prolonged use.

Durability is another critical aspect of the IM826-A. The rugged construction of the unit ensures it can withstand the challenging environments often found in industrial settings. Its compact design makes it suitable for both shop and field use, enabling welders to work efficiently in various locations.

Overall, the Lincoln Electric IM826-A represents a significant advancement in welding technology. Its multi-process capability, inverter technology, intuitive control system, safety features, and robust design make it a preferred choice for professional welders. With the IM826-A, users can expect high performance, efficiency, and reliability, further solidifying Lincoln Electric's reputation as a leader in the welding industry.
Top Page Image Contents