28.Use proper accessories. Consult this manual for recommended accessories. Using improper accessories may be hazardous. Be sure accessories are properly installed and maintained. Do not de- feat a guard or other safety device when installing an accessory or attachment.
29.Maintain tools carefully. Keep handles dry, clean and free from oil and grease. Keep cutting edges sharp and clean. Follow instruc- tions for lubricating and changing accessories. Periodically inspect tool cords and extension cords for damage. Have damaged parts repaired or replaced by a MILWAUKEE service facility.
30.Maintain labels & nameplates. These carry important informa- tion. If unreadable or missing, contact a MILWAUKEE service facil- ity for a free replacement.
SERVICE
31.Tool service must be performed only by qualified repair personnel. Service or maintenance performed by unqualified per- sonnel may result in a risk of injury.
32.When servicing a tool, use only identical replacement parts. follow instructions in the maintenance section of this manual. Use of unauthorized parts or failure to follow maintenance instructions may create a risk of shock or injury.
SPECIFIC SAFETY RULES
1.WARNING! Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals known to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are:
•lead from
•crystalline silica from bricks and cement and other masonry products, and
•arsenic and chromium from
Your risk from these exposures varies, depending on how often you do this type of work. To reduce your exposure to these chemi- cals: work in a well ventilated area, and work with approved safety equipment, such as those dust masks that are specifically designed to filter out microscopic particles.
2.Always keep hands away from the path of the saw blade.
3.Do not defeat the guards of operate the tool without the guards in place.
4.Always support work properly. Use the fence, support blocks, auxiliary work support or clamps to keep workpiece secure. Al- ways support the free end of the workpiece and support all small workpieces. Workpieces that bow and pinch the blade may result in kick back. Do not perform any operations freehand (unsupported).
5.Never reach around, under or across blade.
6.Check guards for smooth operation before each use.
7.Avoid kick back. Kick back is a violent reaction to a pinched or binding blade, which throws the saw head upward and towards the operator. Proper workpiece selection and support, proper blade selection and maintenance, and even feed rate are essential to reduce the risk of kick back.
8.Always wait for the blade to stop completely before chang- ing positions, retrieving a
9.Be sure the clamp handle and the bevel adjustment lever are tightened securely before making cuts.
10.Do not use abrasive wheels with the miter saw.
11.Use the right blade. Use only recommended blade types and sizes with proper mounting holes, rated at least 5500 RPM. Follow the rotation arrow on the blade to be sure you install it properly. Keep saw blades sharp to help prevent cracking and grabbing. Never use defective or incorrect washers or bolts.
12.Do not lock the trigger in the on position.
13.Wait for the blade to reach full speed before lowering the saw head to make a cut.
14.Keep the cord away from the cutting area and position it so that it will not be tripped over or caught on the workpiece while you are cutting.
15.Do not place hands under the saw motor or in the path of the blade. Do not retrieve a piece of material that is cut off while the blade is rotating. Never place hands or fingers behind or in front of the saw blade.
16.Keep blades clean and sharp. An unsharpened or improperly sharpened blade produces a narrow kerf and is likely to be pinched by the workpiece. A dull blade produces excessive friction which can cause the blade to warp or bind. Be sure the blade screw is tight to prevent slipping or loosening during operation.
17.Restarting in
18.If the blade stalls, do not turn the switch on and off. A dull blade or excess pressure may cause stalling. Release the switch immediately if the blade binds or the saw stalls and remove the saw from the cut.
19.Avoid cutting nails. Inspect for and remove all nails before cutting.
20.Thin material tends to warp or sag and must be
21.Position fence properly. The flip fence can be adjusted for com- pound cuts and miter cuts. Always make sure the fence is adjusted for the intended cut. Never operate the saw without the fence in place.
22.Lock the saw head down and lock the sliding mechanism before transporting.
23.Push the saw through the workpiece. Do not pull the saw through the workpiece. To make a cut, raise saw head and pull it out OVER the workpiece WITHOUT cutting, start the motor, wait a few seconds for the blade to reach full speed, press down on saw head, and push saw head through the cut.
page 4