Xantrex Technology TC2 204060 manual FCC Information to the User, Viii

Page 10

TC2 204060 Series BattChg Owners Guide.book Page viii Friday, July 8, 2011 11:44 AM

FCC Information to the User

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

•Reorient or relocate the receiving antenna.

•Increase the separation between the equipment and receiver.

•Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

•Consult the dealer or an experienced radio/TV technician for help.

Unauthorized changes or modifications to the equipment could void the user’s authority to operate the equipment.

		viii				Truecharge2 Series Battery Charger Owner’s Guide

Image 10

Contents Series Battery Charger Page Exclusion for Documentation TrademarksProduct Numbers Date and RevisionAbout This Guide Statement of HazardRelated Information Important Safety Instructions Electrical Shock HazardExplosion Hazard Fire and Burn HazardPersonal Injury Hazard Precautions When Working With Batteries Risk of Damage to the Battery Charger Precautions When Placing the Battery ChargerExposure to Chemicals and Gases Hazard FCC Information to the User ViiiContents Page Standard and Protection Features Truecharge2 Battery ChargerIntroduction Introduction Truecharge 2 Battery Charger Features Front PanelRear Panel Truecharge2 Series Battery Charger Owner’s GuideAC wiring compartment DescriptionOnboard Control and Status Display Panel Item DescriptionTruecharge2 Series Battery Charger Owner’s Guide Risk of Battery Damage Preparing For Installation Improper Installation by AN Unqualified InstallerTools and Materials You need the following materialsCondition Requirement LocationExplosion Hazard for IEC Models only Mounting Orientations Deck and Horizontal Wiring Requirements Electrical Shock and Fire HazardDC Wiring Wire Length Wire Size AWG and mm2AWG Fire HazardInjury Battery Bank Size Requirements Other examples of AC wiring requirementsMounting the Battery Charger Installing the Truecharge 2 Battery ChargerInstallation Sequence To mount the Truecharge2 Battery ChargerConnecting the DC Chassis Ground Earth To connect the DC chassis ground earthAccidental Short or Spark Hazard Installing DC WiringShock Hazard For more than one battery or bank For one battery or bankReverse Polarity Damage Installing the Truecharge 2 Battery Charger Installing AC Wiring AC wiring access holeConductor Charger Pigtail AC Supply Wire Color Code Tapered end of strain relief AC supply wiringScrew to secure the wiring compartment cover Powering Up Explosion AND/OR Fire HazardInstalling a Parallel Configuration Damage to the Battery ChargerWhen Configuring the Battery Chargers Powering up after installing a parallel configurationFault and Warning Conditions When Equalizing BatteriesInstalling Batteries Input Voltage Operating and DeratingMulti-Stage Charging AC sourceThree-Stage Charging Two-Stage Charging To force a battery detection sequence Battery QualificationTemperature Considerations Charging Voltage SetpointsSetting the Battery Temperature without a BTS Operating DC Loads Configuring the Charger Mode Configuring the Truecharge2 Battery ChargerConfiguring the Battery Bank Type Charging Batteries Mode Charger Status LED-ONTo charge your batteries Charging Batteries Equalizing Flooded Batteries EXPLOSION, FIRE, and Burn Hazards Performing An EqualizationRisk of Equipment Damage To equalize your batteriesEqualizing Flooded Batteries Transitioning the Charger to ON, Standby, or Disabled Reading Onboard Display LEDs Accessing Charger InformationReporting While Charging or Equalizing Reporting Without AC Power or While on StandbyFault or Warning Solution Condition Fuse on Using a Generator As Source Power Maintaining the Charger Improper Installation by AN Unqualified Installer Replacing the DC Output FuseFuse Replacement Ratings ModelTroubleshooting Possible Cause SolutionTroubleshooting Disconnect all loads or switch loads off 975-0526-01-02 Troubleshooting Specifications Physical Specifications AC Input SpecificationsDC Output Specifications Environmental Specifications Protection Features Regulatory ApprovalsWarranty and Return Information WarrantyWarranty and Return Information Disclaimer ProductReturn Procedure Return Material Authorization PolicyOut of Warranty Service Information About Your System Page Xantrex Technology USA Inc