Xantrex Technology TC2 204060 manual Truecharge 2 Battery Charger Features, Front Panel

Page 15

TC2 204060 Series BattChg Owners Guide.book Page 3 Friday, July 8, 2011 11:44 AM

Truecharge 2 Battery Charger Features

This section describes the different parts of the Truecharge2 Battery Charger.

Front Panel

1

2

3

4 5

6

Figure 1 Truecharge2 Battery Charger Front Panel

Item

Description

1Onboard control and status display panel or simply onboard display (see “Onboard Control and Status Display Panel” on page 5 for more information) for controlling the Truecharge2 Battery Charger settings and for monitoring charger status and charging current.

2Mounting flanges are used to permanently install the product.

3DC wiring compartment cover protects the DC terminals, as well as the communication and BTS ports. Remove and replace when installing cables.

ELECTRICAL SHOCK HAZARD

Disconnect the batteries and AC power before opening the fuse access panel.

Failure to follow these instructions will result in death or serious injury.

4Fuse access panel cover provides access to the DC fuse in the event of an accidental reverse battery polarity installation. Remove and replace the cover when replacing a fuse or fuses.

 

 

975-0526-01-02

3

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Image 15
Contents Series Battery Charger Page Date and Revision TrademarksProduct Numbers Exclusion for DocumentationStatement of Hazard About This GuideRelated Information Electrical Shock Hazard Important Safety InstructionsFire and Burn Hazard Explosion HazardPersonal Injury Hazard Precautions When Working With Batteries Precautions When Placing the Battery Charger Risk of Damage to the Battery ChargerExposure to Chemicals and Gases Hazard Viii FCC Information to the UserContents Page Truecharge2 Battery Charger Standard and Protection FeaturesIntroduction Introduction Front Panel Truecharge 2 Battery Charger FeaturesDescription Truecharge2 Series Battery Charger Owner’s GuideAC wiring compartment Rear PanelItem Description Onboard Control and Status Display PanelTruecharge2 Series Battery Charger Owner’s Guide Risk of Battery Damage Improper Installation by AN Unqualified Installer Preparing For InstallationYou need the following materials Tools and MaterialsLocation Condition RequirementExplosion Hazard for IEC Models only Mounting Orientations Deck and Horizontal Electrical Shock and Fire Hazard Wiring RequirementsWire Length Wire Size AWG and mm2 DC WiringFire Hazard AWGInjury Other examples of AC wiring requirements Battery Bank Size RequirementsTo mount the Truecharge2 Battery Charger Installing the Truecharge 2 Battery ChargerInstallation Sequence Mounting the Battery ChargerTo connect the DC chassis ground earth Connecting the DC Chassis Ground EarthInstalling DC Wiring Accidental Short or Spark HazardShock Hazard For one battery or bank For more than one battery or bankReverse Polarity Damage Installing the Truecharge 2 Battery Charger AC wiring access hole Installing AC WiringTapered end of strain relief AC supply wiring Conductor Charger Pigtail AC Supply Wire Color CodeScrew to secure the wiring compartment cover Explosion AND/OR Fire Hazard Powering UpDamage to the Battery Charger Installing a Parallel ConfigurationWhen Equalizing Batteries Powering up after installing a parallel configurationFault and Warning Conditions When Configuring the Battery ChargersInput Voltage Operating and Derating Installing BatteriesAC source Multi-Stage ChargingThree-Stage Charging Two-Stage Charging Charging Voltage Setpoints Battery QualificationTemperature Considerations To force a battery detection sequenceSetting the Battery Temperature without a BTS Operating DC Loads Configuring the Truecharge2 Battery Charger Configuring the Charger ModeConfiguring the Battery Bank Type Mode Charger Status LED-ON Charging BatteriesTo charge your batteries Charging Batteries Equalizing Flooded Batteries To equalize your batteries Performing An EqualizationRisk of Equipment Damage EXPLOSION, FIRE, and Burn HazardsEqualizing Flooded Batteries Transitioning the Charger to ON, Standby, or Disabled Accessing Charger Information Reading Onboard Display LEDsReporting While Charging or Equalizing Standby Reporting Without AC Power or While onFault or Warning Solution Condition Fuse on Using a Generator As Source Power Maintaining the Charger Replacing the DC Output Fuse Improper Installation by AN Unqualified InstallerModel Fuse Replacement RatingsPossible Cause Solution TroubleshootingTroubleshooting Disconnect all loads or switch loads off 975-0526-01-02 Troubleshooting Physical Specifications AC Input Specifications SpecificationsDC Output Specifications Environmental Specifications Regulatory Approvals Protection FeaturesWarranty Warranty and Return InformationWarranty and Return Information Product DisclaimerReturn Material Authorization Policy Return ProcedureOut of Warranty Service Information About Your System Page Xantrex Technology USA Inc