Xantrex Technology TC2 204060 manual DC Output Specifications

Page 67

TC2 204060 Series BattChg Owners Guide.book Page 55 Friday, July 8, 2011 11:44 AM

Specifications

DC Output Specifications

DC Output Specifications

Number of isolated battery

3 separated outputs

bank outputs

 

 

 

DC output voltage range

 

including dead battery

 

charging voltage

 

12-volt units:

0 – 16 Vdc

24-volt units:

0 – 32 Vdc

 

 

Maximum equalization

 

voltage

 

12-volt units:

16 Vdc

24-volt units:

32 Vdc

 

 

Voltage accuracy (no load)

 

12-volt units:

14.4 ±0.1 Vdc @ 25 °C (77 °F)

24-volt units:

28.8 ±0.2 Vdc @ 25 °C (77 °F)

 

 

Nominal battery voltage

 

12-volt units:

12 Vdc

24-volt units:

24 Vdc

 

 

Normal operating output

 

 

 

range

 

 

 

12-volt units:

0 – 16 Vdc

 

24-volt units:

0 – 32 Vdc

 

 

 

 

 

Maximum DC output

 

 

 

current (total)

 

 

 

TC2012:

20

+10% A

 

TC4012:

40

+10% A

 

TC6012

60

+10% A

 

TC1024:

10

+10% A

 

TC2024:

20

+10% A

 

TC3024:

30

+10% A

 

 

 

 

 

Absorption voltage:

12-volt units

24-volt units

 

Flooded

25

°C (77 °F)

25 °C (77 °F)

14.4 ±0.1

28.8 ±0.2

GEL

14.2 ±0.1

28.4 ±0.2

AGM

14.3 ±0.1

28.6 ±0.2

Lead-calcium

15.5 ±0.1

31.0 ±0.2

 

 

 

 

 

 

975-0526-01-02

55

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Page 66 Page 68
Image 67
Page 66 Page 68
Contents Series Battery Charger Page Date and Revision TrademarksProduct Numbers Exclusion for DocumentationStatement of Hazard About This GuideRelated Information Electrical Shock Hazard Important Safety InstructionsExplosion Hazard Fire and Burn HazardPersonal Injury Hazard Precautions When Working With Batteries Risk of Damage to the Battery Charger Precautions When Placing the Battery ChargerExposure to Chemicals and Gases Hazard Viii FCC Information to the UserContents Page Standard and Protection Features Truecharge2 Battery ChargerIntroduction Introduction Front Panel Truecharge 2 Battery Charger FeaturesDescription Truecharge2 Series Battery Charger Owner’s GuideAC wiring compartment Rear PanelItem Description Onboard Control and Status Display PanelTruecharge2 Series Battery Charger Owner’s Guide Risk of Battery Damage Improper Installation by AN Unqualified Installer Preparing For InstallationYou need the following materials Tools and MaterialsCondition Requirement LocationExplosion Hazard for IEC Models only Mounting Orientations Deck and Horizontal Electrical Shock and Fire Hazard Wiring RequirementsWire Length Wire Size AWG and mm2 DC WiringAWG Fire HazardInjury Other examples of AC wiring requirements Battery Bank Size RequirementsTo mount the Truecharge2 Battery Charger Installing the Truecharge 2 Battery ChargerInstallation Sequence Mounting the Battery ChargerTo connect the DC chassis ground earth Connecting the DC Chassis Ground EarthAccidental Short or Spark Hazard Installing DC WiringShock Hazard For more than one battery or bank For one battery or bankReverse Polarity Damage Installing the Truecharge 2 Battery Charger AC wiring access hole Installing AC WiringTapered end of strain relief AC supply wiring Conductor Charger Pigtail AC Supply Wire Color CodeScrew to secure the wiring compartment cover Explosion AND/OR Fire Hazard Powering UpDamage to the Battery Charger Installing a Parallel ConfigurationWhen Equalizing Batteries Powering up after installing a parallel configurationFault and Warning Conditions When Configuring the Battery ChargersInput Voltage Operating and Derating Installing BatteriesAC source Multi-Stage ChargingThree-Stage Charging Two-Stage Charging Charging Voltage Setpoints Battery QualificationTemperature Considerations To force a battery detection sequenceSetting the Battery Temperature without a BTS Operating DC Loads Configuring the Charger Mode Configuring the Truecharge2 Battery ChargerConfiguring the Battery Bank Type Charging Batteries Mode Charger Status LED-ONTo charge your batteries Charging Batteries Equalizing Flooded Batteries To equalize your batteries Performing An EqualizationRisk of Equipment Damage EXPLOSION, FIRE, and Burn HazardsEqualizing Flooded Batteries Transitioning the Charger to ON, Standby, or Disabled Reading Onboard Display LEDs Accessing Charger InformationReporting While Charging or Equalizing Standby Reporting Without AC Power or While onFault or Warning Solution Condition Fuse on Using a Generator As Source Power Maintaining the Charger Replacing the DC Output Fuse Improper Installation by AN Unqualified InstallerModel Fuse Replacement RatingsPossible Cause Solution TroubleshootingTroubleshooting Disconnect all loads or switch loads off 975-0526-01-02 Troubleshooting Physical Specifications AC Input Specifications SpecificationsDC Output Specifications Environmental Specifications Regulatory Approvals Protection FeaturesWarranty Warranty and Return InformationWarranty and Return Information Product DisclaimerReturn Procedure Return Material Authorization PolicyOut of Warranty Service Information About Your System Page Xantrex Technology USA Inc
Top Page Image Contents