DeWalt D55167 Preparation For Use Pre-Start Checklist Fig, Operating Procedures Start-up Fig

Page 12

English

Lifting

 

 

Always use two people when lifting and lift from

N

N

the recommended lift points (N). DO NOT lift

 

 

 

by wheels or shroud.

 

 

Moving

CAUTION: The wheels and handle do not provide adequate clearance, stability, or

support for pulling the unit up and down stairs or steps. The unit must be lifted or pushed up a ramp.

1.Grasp handle of compressor and tilt compressor back to rest on wheels.

Warning: Risk of Unsafe Operation. Ensure proper footing and use caution when rolling compressor so that unit does not tip or cause loss of balance.

2.When location is reached slowly lower compressor to ground.

Always store compressor in a horizontal position resting on the rubber bumpers and wheels.

Preparation For Use

WARNING: Do not operate this unit until you read this instruction manual for safety, operation and maintenance instructions.

Pre-Start Checklist (Fig. 1)

1.Ensure the Auto/Off switch (A) is in the OFF position.

2.Plug the power cord into the correct branch circuit receptacle. See Voltage and Circuit Protection under Installation.

3.Ensure air tank is drained, see Draining Air Tank under Maintenance.

4.Ensure the drain valve (H) is closed.

5.Ensure safety valve (G) is functioning properly, see Checking Safety Valve under Maintenance.

6.Pull the regulator knob (D) out and turn counterclockwise until fully closed. Ensure regulated pressure gauge reads 0 psi. Push knob in to lock in place.

7.Attach hose and accessories. NOTE: Always use a minimum 3/8" (9.5 mm) or greater air hose rated at 300 psi.

Warning: Risk of unsafe operation. Firmly grasp air hose in hand when installing or disconnecting to prevent hose whip.

Warning: Risk of unsafe operation. Do not use damaged or worn accessories.

Warning: Risk of Bursting. Too much air pressure causes a hazardous risk of bursting. Check the manufacturer’s maximum pressure rating for air tools and accessories. The regulator outlet pressure must never exceed the maximum pressure rating.

Operating Procedures

Start-up (Fig. 1)

1.Follow Pre-Start Checklist under Preparation for Use.

2.Move the Auto/Off switch to the AUTO position and allow tank pressure to build. Motor will stop when tank pressure reaches cut‑out pressure.

NOTICE: Risk of property damage. Compressed air from the unit may contain wa­ter condensation and oil mist. Do not spray un­fil­ tered air at an item that could be damaged by moisture. Some air oper­ated­ tools or devic­es­ may require filtered air. Read the instruc­­ tions for the air tool or device.

3.Adjust regulator (D) to desired setting. See Regulator under Features.

Shut-down (Fig. 1)

1.Move Auto/Off switch (A) to the OFF position. NOTE: If finished using compressor, follow Steps 2 - 6.

12

Page 11 Page 13
Image 12
Page 11 Page 13
Contents D55167 Pump/Motor Specifications SpecificationsD55167 Air Compressor Declared Noise Emission Values per ISODefinitions Safety Guidelines Important Safety InstructionsWhat can happen How to prevent it Save these instructionWith the product when it is Unit when not in useRestricting any Compressor ventilationAttachments & accessories TIres Electrical GroundingSee Grounding Instructions underBy a DeWALT factory service Service centerMoving parts such as Cause serious injury if theyNever defeat the safety fea­ Air compressorCompressor at all times Use additional air hose to reach high locationsFeatures Fig Assembly Grounding InstructionsAIR Intake Filter Extension Cords Voltage and Circuit ProtectionCompatibility Location ElectricalPreparation For Use Pre-Start Checklist Fig Operating Procedures Start-up FigShut-down Fig Maintenance Maintenance ChartChecking Safety Valve Procedure Daily Weekly See tankAccessories Service Information Draining Air Tank FigChecking Air Filter Element Fig RepairsFull One Year Warranty GlossaryTroubleshooting Guide Troubleshooting CodesProblem Code Possible SolutionExplode Check for proper fuse. You should use a time delay fuse Area. See Risk of Explosion or Fire warning under ImportantFuse blown, circuit breaker tripped Compressor on its own branch circuitCompresseur d’air, modèle D55167 Fiche technique de la pompe/du moteurFiche technique Définitions Lignes directrices en Matière de sécurité Conserver ces directivesDirectives de sécurité importantes Après toute manipulationVapeurs inflammables ExplosionSi vous aspergez des Matériaux inflammablesAvertissement risque d’Éclatement Accessoires  Ce qui peut se produirePneus Avertissement risque de choc Électrique Avertissement risque provenant des Objets projetÉs en l’airAvertissement risque associÉ Aux piÈces mobiles Avertissement attention surfaces chaudesAvertissement risque associÉ À Utilisation dangereuse CE QUI Peut SE ProduireCaractÉristiques FIG Assemblage Filtre D’ADMISSION D’AIRDirectives relatives à la mise à la terre RallongesProtection de la tension et du circuit Électricien qualifiéEmplacement CompatibilitéMode d’emploi Liste de vérification de pré-démarrage FigProcédures de fonctionnement Démarrage Fig Arrêt FigEntretien Programme d’entretienProcédure Quoti Hebdo Se reporter Vérification de la soupape de sûreté Vidange du réservoir d’air FigVérification des éléments du filtre d’air Fig Accessoires Information sur les réparationsRéparations Garantie complète d’un 1 anRemplacement Gratuit DES Étiquettes GlossaireSolution Probable Guide de dépannageCodes de dépannage Problème CodeDe l’accessoire Ou d’exploserConsulter la rubrique Surcharge du moteur sous Lire l’avertissement concernant les risque d’explosion ouFrançais Compresor de aire D55167 Especificaciones de la Bomba y el MotorEspecificaciones Valores de emisión de ruido declarados según ISODefiniciones Normas de seguridad Guarde estas instruccionesInstrucciones de seguridad importantes Peligro Riesgo de explosión o incendioPeligro Riesgo Respiratorio asfixia Advertencia Riesgo de explosión ¿Qué puede suceder?Elementos y accesorios Advertencia riesgo de descarga eléctricaNeumáticos Advertencia Riesgo de objetos despedidos Advertencia Riesgo DE superficies calientesAdvertencia riesgo por piezas móviles Advertencia Riesgo de operación inseguraCaracterísticas FIG Atención riesgo por ruidosInterruptor de Auto/apagado ¿Qué puede suceder? Cómo evitarlo Interruptor de presiónFiltro DE Entrada DE Aire Instrucciones de conexión a tierra EnsamblajeInstalación de las mangueras Desconexión de las manguerasCables prolongadores Voltaje y protección del circuitoCompatibilidad LugarPreparación para el uso Lista de control previa a la puesta en marcha FigAdvertencia Riesgo Procedimientos operativos Puesta en marcha Fig Apagado FigMantenimiento Tabla de mantenimiento Controlar la válvula de seguridadDrenar el tanque de aire Fig Controlar el elemento del filtro de aire Fig AccesoriosPóliza de Garantía Sello o firma del DistribuidorGarantía completa de un año ExcepcionesCULIACAN, SIN Glosario Guía de detección de problemas Códigos de detección de problemasSolución Posible Sellos de pérdidas Centro de servicio autorizado DeWALTVálvula de seguridad defectuosa Válvula aún pierde, debe ser reemplazadaLa presión del tanque excede la presión de Posible motor defectuososSección Mantenimiento Page Page EWALT Industrial Tool Co., 701 Joppa Road, Baltimore, MD
Top Page Image Contents