DeWalt D55167 instruction manual Features Fig

Page 9

SAVE THESE INSTRUCTIONS

FOR FUTURE USE

Tank Pressure Gauge

The tank pressure gauge (B) indicates the reserve air pressure in the tank.

Features (Fig. 1)

Auto/Off Switch

Place this switch (A) in the AUTO (I) position to provide automatic power to the pressure switch and OFF (O) to remove power at the end of each use.

Pressure Switch

A

 

I

f

regulated Pressure Gauge

The outlet pressure gauge (C) indicates the air pressure available at the outlet side of the regulator. This pressure is controlled by the regulator and is always less than or equal to the tank pressure.

Regulator

The regulator (D) controls the air pressure shown on the regulated pressure gauge. Pull the knob out and turn clockwise to increase pressure and counterclockwise to decrease pressure. When the

English

The pressure switch (I) automatically starts the motor when the air tank pressure drops below the factory set cut-inpressure. It stops the motor when the air tank pressure reaches the factory set cut‑out pressure.

Safety Valve

desired pressure is reached push knob in to lock in place.

Universal Quick Connect BodY

The universal quick connect body (E) accepts the three most popular styles of quick connect plugs: Industrial, automotive, and ARO. One hand push-to-connect operation makes connections simple and easy.

If the pressure switch does not shut off the air compressor at its cut-out pressure setting, the safety valve (G) will protect against high pressure by popping out at its factory set pressure (slightly higher than the pressure switch cut-out setting).

Check Valve

D

B

C

E

G

Drain Valve

 

The drain valve (H) is located at the base of the air

 

tank and is used to drain condensation at the end

 

of each use. See Draining Air Tank under

 

Maintenance.

 

Cooling System

H

 

This compressor contains an advanced design cooling system. It is normal for this fan to blow air through the vent holes in large

When the air compressor is operating, the check valve (F) is open, allowing compressed air to enter the air tank. When the air compressor reaches cut-out pressure, the check valve closes, allowing air pressure to remain inside the air tank.

amounts. The cooling system is working when air is expelled.

Air Compressor Pump

The pump compresses air into the air tank. Working air is not available until the compressor has raised the air tank pressure above that required at the air outlet.

9

Page 8 Page 10
Image 9
Page 8 Page 10
Contents D55167 Specifications Pump/Motor SpecificationsD55167 Air Compressor Declared Noise Emission Values per ISOImportant Safety Instructions Definitions Safety GuidelinesWhat can happen How to prevent it Save these instructionUnit when not in use With the product when it isRestricting any Compressor ventilationAttachments & accessories Electrical Grounding TIresSee Grounding Instructions underService center By a DeWALT factory serviceMoving parts such as Cause serious injury if theyAir compressor Never defeat the safety fea­Compressor at all times Use additional air hose to reach high locationsFeatures Fig Assembly Grounding InstructionsAIR Intake Filter Voltage and Circuit Protection Extension CordsCompatibility Location ElectricalPreparation For Use Pre-Start Checklist Fig Operating Procedures Start-up FigShut-down Fig Maintenance Chart MaintenanceChecking Safety Valve Procedure Daily Weekly See tankDraining Air Tank Fig Accessories Service InformationChecking Air Filter Element Fig RepairsGlossary Full One Year WarrantyTroubleshooting Codes Troubleshooting GuideProblem Code Possible SolutionExplode Area. See Risk of Explosion or Fire warning under Important Check for proper fuse. You should use a time delay fuseFuse blown, circuit breaker tripped Compressor on its own branch circuitCompresseur d’air, modèle D55167 Fiche technique de la pompe/du moteurFiche technique Conserver ces directives Définitions Lignes directrices en Matière de sécuritéDirectives de sécurité importantes Après toute manipulationExplosion Vapeurs inflammablesSi vous aspergez des Matériaux inflammablesAvertissement risque d’Éclatement Accessoires  Ce qui peut se produirePneus Avertissement risque provenant des Objets projetÉs en l’air Avertissement risque de choc ÉlectriqueAvertissement attention surfaces chaudes Avertissement risque associÉ Aux piÈces mobilesCE QUI Peut SE Produire Avertissement risque associÉ À Utilisation dangereuseCaractÉristiques FIG Filtre D’ADMISSION D’AIR AssemblageRallonges Directives relatives à la mise à la terreProtection de la tension et du circuit Électricien qualifiéCompatibilité EmplacementListe de vérification de pré-démarrage Fig Mode d’emploiProcédures de fonctionnement Démarrage Fig Arrêt FigEntretien Programme d’entretienProcédure Quoti Hebdo Se reporter Vérification de la soupape de sûreté Vidange du réservoir d’air FigVérification des éléments du filtre d’air Fig Information sur les réparations AccessoiresRéparations Garantie complète d’un 1 anGlossaire Remplacement Gratuit DES ÉtiquettesGuide de dépannage Solution ProbableCodes de dépannage Problème CodeOu d’exploser De l’accessoireLire l’avertissement concernant les risque d’explosion ou Consulter la rubrique Surcharge du moteur sousFrançais Especificaciones de la Bomba y el Motor Compresor de aire D55167Especificaciones Valores de emisión de ruido declarados según ISOGuarde estas instrucciones Definiciones Normas de seguridadInstrucciones de seguridad importantes Peligro Riesgo de explosión o incendioPeligro Riesgo Respiratorio asfixia ¿Qué puede suceder? Advertencia Riesgo de explosiónElementos y accesorios Advertencia riesgo de descarga eléctricaNeumáticos Advertencia Riesgo DE superficies calientes Advertencia Riesgo de objetos despedidosAdvertencia Riesgo de operación insegura Advertencia riesgo por piezas móvilesAtención riesgo por ruidos Características FIGInterruptor de Auto/apagado ¿Qué puede suceder? Cómo evitarlo Interruptor de presiónFiltro DE Entrada DE Aire Ensamblaje Instrucciones de conexión a tierraInstalación de las mangueras Desconexión de las manguerasVoltaje y protección del circuito Cables prolongadoresCompatibilidad LugarPreparación para el uso Lista de control previa a la puesta en marcha FigAdvertencia Riesgo Procedimientos operativos Puesta en marcha Fig Apagado FigMantenimiento Tabla de mantenimiento Controlar la válvula de seguridadDrenar el tanque de aire Fig Accesorios Controlar el elemento del filtro de aire FigPóliza de Garantía Sello o firma del DistribuidorExcepciones Garantía completa de un añoCULIACAN, SIN Glosario Guía de detección de problemas Códigos de detección de problemasSolución Posible Centro de servicio autorizado DeWALT Sellos de pérdidasVálvula de seguridad defectuosa Válvula aún pierde, debe ser reemplazadaPosible motor defectuosos La presión del tanque excede la presión deSección Mantenimiento Page Page EWALT Industrial Tool Co., 701 Joppa Road, Baltimore, MD
Top Page Image Contents