Multiquip Sp-6065 operation manual Stacking Blades for Wide Cuts, Blade Stacking

Page 24

Stacking Blades for Wide Cuts

WARNING

NEVER attempt to stack blades beyond the capacity of the Kits described here. NEVER operate the saw without blade guards in place.

Combining (stacking) blades together to make wide cuts requires an optional

Bushing Extension Kit.

Kit #18501 allows blade stacking from .375” to .75” thickness.

Kit #18502 allows blade stacking from .75” to 1.125” thickness.

The kits consist of an outer collar with a longer pin, an extended bushing, and

longer bolts.

1.Remove the existing Blade (see Installing the Blade, above).

2.Replace the standard Collar Bushing, Outer Collar, and Mounting Bolt that came with the saw, with the extended Bolt and Bushing and the new Outer Collar that came with the Kit.

The Mounting Bolt for the right side of the saw (as seen from the operator’s position) has a left hand-thread, while the Mounting Bolt for the left side of the saw has a right-hand thread.

3.Insert the Bushing and Mounting Bolt through the Outer Collar and stack of Blades. The longer bushing and bolt allow blades to be stacked together

4.Align the Collar Pin through the stack of Blades into the Inner Collar.

5.Tighten the 5/8” Mounting Bolt to 125-175 foot-pounds of torque.

Outer Collar with extended pin

Extended bushing

Extended bolt

Inner Collar

Fig. 6 — Blade Stacking

24

Image 24
Contents SP-6065 Concrete Saw For Help & Information Contact Multiquip Conventions California Proposition 65 Warning Table of Contents Specifications Safety Hazard Symbols Rotating Blades Skin Injection Hazard General Safety Warnings Rules for Safe OperationPage General Safety Precautions Blade Safety SAW Transportation Safety Machine Operation and Safety Decals Serial Tag Model no SPEC. no Serial noSerial TAG Operation Before StartingEngine Power, Cutting Power & Sheave Size Blade Shaft Ratios18600 Blade RPM vs. Surface Feet Per Minute Sfpm Installing the Blade Installing the BladeStacking Blades for Wide Cuts Blade StackingInstalling and Removing the Blade Guard Installing the Blade GuardBlade Guard Water Supply Installing the Collar Guard Collar Guard, InstalledWater Supply and Control Water Supply SystemControl Panel ON-OFFHandlebars Handlebar Positions Similar to illustrationFueling the Saw Fuel SystemON/OFF Switch, Choke, Throttle Locations Starting and Stopping the EnginePointer Adjustment Block HeatersDraining the Water System Pointer Adjustment Setting the Depth Indicator Raise Lower ControlsSetting the Depth Stop Drive System Drive System ControlsTransaxle TransaxleNight Light Transportation Tie-downs and Lift PointTie-downs Lift Point Lift PointMaintenance Removable Guards and Access PanelsBelts and Pulleys Belt TensionAdjusting Blade Shaft Drive Belt Tension Engine Mount Lock BoltsReplacing the Blade Shaft Belt Replacing the Jackshaft BeltRotary Belt Tensioner Do not OVER-TIGHTENBlade Shaft Maintenance Blade Shaft ReplacementBlade Collar Removal/Installation Removing the Inner Blade CollarInstalling the Inner Blade Collar Installing the Inner Blade CollarInner Collar Blade Shaft Maximum Cut Depth Adjustment Circuit BreakersLubrication Air and Oil Filter Chart EnginePTO Drive Maintenance Attaching the PTO Bearing Puller to the Drive Plate AssemblyPTO Drive Sheave/Bearing Assembly Re-Assembling the PTO DriveReplacing the Battery Rotate Engine Forward to Remove the BatteryRaise/Lower Troubleshooting Raise-Lower SystemJoystick Tension Adjustment Joystick AdjustmentHydraulic System Maintenance Routine MaintenanceDraining & Filling the Hydraulic System To drain the hydraulic systemTo fill the hydraulic system with oil Bleeding the Depth Stop Cylinder Bleeding the Depth Stop CylinderDrive Wheel Alignment Drive Wheel AlignmentPivot Side Adjustment Side Specifications Dimensions and Weights Www multiquip.com