Multiquip Sp-6065 operation manual Engine, Air and Oil Filter Chart

Page 52

Engine

The Model SP-6065 features a xx HP xx gasoline engine. See the engine manual

for service details and oil recommendations.

∙Check air filters daily, replace as required.

∙Check engine oil level daily.

♦Level the frame prior to service to get an accurate reading.

♦Do Not over-fill with oil.

∙Change engine oil and filter every 50 hours of operation

CAUTION

Safety Air Filters are not intended to be used for primary air

filtration. When the Primary Filter gets clogged, replace it immediately — do not run saw using just the Safety filter.

Air and Oil Filter Chart

Filter

Qty

Part Number

 

 

 

 

Primary Air Filter

1

300004-1

(Donaldson #P827653)

 

 

 

 

Safety Air Filter

1

300004-2

(Donaldson #P829332)

 

 

 

 

Engine Oil Filter

1

306012

(Deutz # 1174416-SP)

 

 

 

 

Hydraulic System Filter

1

306002

(HydroGear # 51563)

Fuel Filter

1 304010 (Donaldson # 1174696)

 

Fuel filter

 

Transaxle

Engine

filter

 

Oil filter

 

 

Fig. 34 — Filters

52

Page 51 Page 53
Image 52
Page 51 Page 53
Contents SP-6065 Concrete Saw For Help & Information Contact Multiquip Conventions California Proposition 65 Warning Table of Contents Specifications Safety Hazard Symbols Rotating Blades Skin Injection Hazard General Safety Warnings Rules for Safe OperationPage General Safety Precautions Blade Safety SAW Transportation Safety Machine Operation and Safety Decals Serial Tag Model no SPEC. no Serial noSerial TAG Operation Before StartingEngine Power, Cutting Power & Sheave Size Blade Shaft Ratios18600 Blade RPM vs. Surface Feet Per Minute Sfpm Installing the Blade Installing the BladeStacking Blades for Wide Cuts Blade StackingInstalling and Removing the Blade Guard Installing the Blade GuardBlade Guard Water Supply Installing the Collar Guard Collar Guard, InstalledWater Supply and Control Water Supply SystemControl Panel ON-OFFHandlebars Handlebar Positions Similar to illustrationFueling the Saw Fuel SystemON/OFF Switch, Choke, Throttle Locations Starting and Stopping the EngineBlock Heaters Pointer AdjustmentDraining the Water System Pointer Adjustment Setting the Depth Indicator Raise Lower ControlsSetting the Depth Stop Drive System Drive System ControlsTransaxle TransaxleTransportation Tie-downs and Lift Point Night LightTie-downs Lift Point Lift PointMaintenance Removable Guards and Access PanelsBelts and Pulleys Belt TensionAdjusting Blade Shaft Drive Belt Tension Engine Mount Lock BoltsReplacing the Blade Shaft Belt Replacing the Jackshaft BeltRotary Belt Tensioner Do not OVER-TIGHTENBlade Shaft Maintenance Blade Shaft ReplacementBlade Collar Removal/Installation Removing the Inner Blade CollarInstalling the Inner Blade Collar Installing the Inner Blade CollarInner Collar Blade Shaft Maximum Cut Depth Adjustment Circuit BreakersLubrication Air and Oil Filter Chart EnginePTO Drive Maintenance Attaching the PTO Bearing Puller to the Drive Plate AssemblyPTO Drive Sheave/Bearing Assembly Re-Assembling the PTO DriveReplacing the Battery Rotate Engine Forward to Remove the BatteryRaise/Lower Troubleshooting Raise-Lower SystemJoystick Tension Adjustment Joystick AdjustmentHydraulic System Maintenance Routine MaintenanceDraining & Filling the Hydraulic System To drain the hydraulic systemTo fill the hydraulic system with oil Bleeding the Depth Stop Cylinder Bleeding the Depth Stop CylinderDrive Wheel Alignment Drive Wheel AlignmentPivot Side Adjustment Side Specifications Dimensions and Weights Www multiquip.com
Top Page Image Contents