Multiquip Sp-6065 operation manual Machine Operation and Safety Decals

Page 16

MACHINE OPERATION AND SAFETY DECALS

The Multiquip SP-6065 Saw is equipped with a number of operation and safety decals. Should any of these decals become unreadable, replacements can be obtained from your dealer.

	P/N 15582		WARNING	P/N 15580
	P/N 15582

			KEEP FEET
			CLEAR
			P/N 25250-001
	WARNING!
KEEP HANDS
	CLEAR
P/N 25249-001
			P/N 15581
	CAUTION
When Larger Blade and Guard
is Installed, Belt Drive MUST
Be Changed to Proper Size.				P/N 22122-001
See Owners Manual.			P/N 11247 (ISO Black)
FAILURE TO COMPLY WITH THE C C AH
JADV EEE AV EEA OIEJGGVCBVVZ
S.M.I. MASONRY AND CONCRETE			P/N 36099 (ISO Blue)
SAW MANUFACTURER’S INSTITUTE
P/N 23330-001
P/N 25491			P/N 25678	P/N 13118
				P/N 13118
				MODEL
				SERIAL NO.
CHECK	LUBRICATION	HOT	BELT DRIVE
DECAL SHEET INTL STDS				CONTACT MULTIQUIP
	P/N 11246			SERVICE DEPARTMENT

16

Image 16

Contents SP-6065 Concrete Saw For Help & Information Contact Multiquip Conventions California Proposition 65 Warning Table of Contents Specifications Safety Hazard Symbols Rotating Blades Skin Injection Hazard General Safety Warnings Rules for Safe OperationPage General Safety Precautions Blade Safety SAW Transportation Safety Machine Operation and Safety Decals Serial Tag Model no SPEC. no Serial noSerial TAG Operation Before StartingEngine Power, Cutting Power & Sheave Size Blade Shaft Ratios18600 Blade RPM vs. Surface Feet Per Minute Sfpm Installing the Blade Installing the BladeStacking Blades for Wide Cuts Blade StackingInstalling and Removing the Blade Guard Installing the Blade GuardBlade Guard Water Supply Installing the Collar Guard Collar Guard, InstalledWater Supply and Control Water Supply SystemControl Panel ON-OFFHandlebars Handlebar Positions Similar to illustrationFueling the Saw Fuel SystemON/OFF Switch, Choke, Throttle Locations Starting and Stopping the EngineBlock Heaters Pointer AdjustmentDraining the Water System Pointer Adjustment Setting the Depth Indicator Raise Lower ControlsSetting the Depth Stop Drive System Drive System ControlsTransaxle TransaxleTransportation Tie-downs and Lift Point Night LightTie-downs Lift Point Lift PointMaintenance Removable Guards and Access PanelsBelts and Pulleys Belt TensionAdjusting Blade Shaft Drive Belt Tension Engine Mount Lock BoltsReplacing the Blade Shaft Belt Replacing the Jackshaft BeltRotary Belt Tensioner Do not OVER-TIGHTENBlade Shaft Maintenance Blade Shaft ReplacementBlade Collar Removal/Installation Removing the Inner Blade CollarInstalling the Inner Blade Collar Installing the Inner Blade CollarInner Collar Blade Shaft Maximum Cut Depth Adjustment Circuit BreakersLubrication Air and Oil Filter Chart EnginePTO Drive Maintenance Attaching the PTO Bearing Puller to the Drive Plate AssemblyPTO Drive Sheave/Bearing Assembly Re-Assembling the PTO DriveReplacing the Battery Rotate Engine Forward to Remove the BatteryRaise/Lower Troubleshooting Raise-Lower SystemJoystick Tension Adjustment Joystick AdjustmentHydraulic System Maintenance Routine MaintenanceDraining & Filling the Hydraulic System To drain the hydraulic systemTo fill the hydraulic system with oil Bleeding the Depth Stop Cylinder Bleeding the Depth Stop CylinderDrive Wheel Alignment Drive Wheel AlignmentPivot Side Adjustment Side Specifications Dimensions and Weights Www multiquip.com