Multiquip Sp-6065 Blade Collar Removal/Installation, Removing the Inner Blade Collar

Page 47

Blade Collar Removal/Installation

Correct removal or installation of the Inner Blade Collar or Flange requires the

Collar Puller (option Part Number 18503) shown in Figure 31.

WARNING

Follow instructions closely to prevent injury from flying Blade Collars! Because of the tapered fit between Blade Collar and Blade Shaft, 5-10 tons of force is needed to release the inner collar. Parts and tools can become dangerous projectiles if instructions are not followed properly.

Fig. 29 — Using the Collar Puller

Removing the Inner Blade Collar

With the Outer Blade Collar in place, and the Blade Mounting Bolt loosened

approximately ¼”:

1.While the three perimeter bolts hold the two Puller Plates together, slide the Horseshoe Plate of the Collar Puller behind the (Shaft) side of the Inner Collar as shown above.

2.Tighten the center Puller bolt to remove the Inner Collar from the Blade Shaft.

♦Having the Outer Collar in place prevents the Puller and Inner Collar from flying off when the taper breaks loose, and causing injury!

♦If the Inner Collar does not readily come free from the tapered Blade Shaft, lightly tap on the central Puller bolt. This should cause the collar to break free from the shaft.

47

Image 47

Contents SP-6065 Concrete Saw For Help & Information Contact Multiquip Conventions California Proposition 65 Warning Table of Contents Specifications Safety Hazard Symbols Rotating Blades Skin Injection Hazard Rules for Safe Operation General Safety WarningsPage General Safety Precautions Blade Safety SAW Transportation Safety Machine Operation and Safety Decals Model no SPEC. no Serial no Serial TagSerial TAG Before Starting OperationBlade Shaft Ratios Engine Power, Cutting Power & Sheave Size18600 Blade RPM vs. Surface Feet Per Minute Sfpm Installing the Blade Installing the BladeBlade Stacking Stacking Blades for Wide CutsInstalling the Blade Guard Installing and Removing the Blade GuardBlade Guard Water Supply Collar Guard, Installed Installing the Collar GuardWater Supply System Water Supply and ControlON-OFF Control PanelHandlebar Positions Similar to illustration HandlebarsFuel System Fueling the SawStarting and Stopping the Engine ON/OFF Switch, Choke, Throttle LocationsDraining the Water System Pointer AdjustmentBlock Heaters Pointer Adjustment Raise Lower Controls Setting the Depth IndicatorSetting the Depth Stop Drive System Controls Drive SystemTransaxle TransaxleTie-downs Night LightTransportation Tie-downs and Lift Point Lift Point Lift PointRemovable Guards and Access Panels MaintenanceBelt Tension Belts and PulleysEngine Mount Lock Bolts Adjusting Blade Shaft Drive Belt TensionReplacing the Jackshaft Belt Replacing the Blade Shaft BeltDo not OVER-TIGHTEN Rotary Belt TensionerBlade Shaft Replacement Blade Shaft MaintenanceRemoving the Inner Blade Collar Blade Collar Removal/InstallationInstalling the Inner Blade Collar Installing the Inner Blade CollarInner Collar Blade Shaft Circuit Breakers Maximum Cut Depth AdjustmentLubrication Engine Air and Oil Filter ChartAttaching the PTO Bearing Puller to the Drive Plate Assembly PTO Drive MaintenanceRe-Assembling the PTO Drive PTO Drive Sheave/Bearing AssemblyRotate Engine Forward to Remove the Battery Replacing the BatteryRaise-Lower System Raise/Lower TroubleshootingJoystick Adjustment Joystick Tension AdjustmentRoutine Maintenance Hydraulic System MaintenanceTo drain the hydraulic system Draining & Filling the Hydraulic SystemTo fill the hydraulic system with oil Bleeding the Depth Stop Cylinder Bleeding the Depth Stop CylinderDrive Wheel Alignment Drive Wheel AlignmentPivot Side Adjustment Side Specifications Dimensions and Weights Www multiquip.com