Grizzly G0460/G0461 Setup Safety Unpacking, Items Needed for Setup, Description Qty

Page 17

SECTION 3: SETUP

Setup Safety

 

Unpacking

 

 

 

 

 

 

This machine presents serious injury hazards to untrained users. Read through this entire manu- al to become familiar with the controls and operations before starting the machine!

Wear safety glasses during

the entire setup process!

The Model G0460/G0461 is a very heavy machine. Serious personal injury may occur if safe mov- ing methods are not fol- lowed. To be safe, get assistance and use power equipment when moving the crate and removing the machine from the crate.

Unsupervised children and visitors inside your shop could cause serious per- sonal injury to themselves. Lock all entrances to the shop when you are away and DO NOT allow unsupervised children or visitors in your shop at any time!

The Model G0460/G0461 was carefully packed when it left our warehouse. If you discover the machine is damaged after you have signed for delivery, please immediately call Customer Service at (570) 546-9663 for advice.

Save the containers and all packing materials for possible inspection by the carrier or its agent. Otherwise, filing a freight claim can be difficult.

When you are completely satisfied with the condi- tion of your shipment, you should inventory the contents.

Items Needed for

Setup

The following items are needed to complete the setup, but are not included with your machine:

Description

Qty

• Safety Glasses (for each person)

1

Forklift or Other Power Lifting Equipment .. 1

• Lifting Straps (1500 lb capacity)

2

• An Assistant to Help with Heavy Items

1

• Main Blade 12" (305mm)

1

• Scoring Blade 3" (80mm)

1

High Quality Straightedge

1

Phillips Head Screwdriver

1

Machinist's Square

1

Framing Square

1

Dust Collection System

1

• 5" Dust Hose and Hose Clamps

1

• 2½" Dust Hose and Hose Clamps

1

G0460/G0461 12" Sliding Table Saw

-15-

Image 17
Contents Sliding Table SAW Page Table of Contents Contact Info IntroductionForeword Machine Data Sheet G0460/G0461 12 Sliding Table Saw Identification Page Safety Instructions for Machinery SafetyAlways Lock Mobile Bases if Used Before Operating Machinery Safety Instructions for Sliding Table Saws Tips to reduce the likelihood of kickback Preventing KickbackProtecting Yourself From Kickback Glossary of Terms Circuit Requirements Grounding Rewiring toMagnetic switch Setup Safety Unpacking SetupItems Needed for Setup Description QtyInventory Qty Clean Up InventoryLock Washers 8mm Small Wing/Table Hardware and ToolsHardware Recognition Chart Site Considerations PlacementMoving & Placing Base Unit Floor LoadBolting to Concrete Floors Mounting to Shop FloorComponents and Hardware Needed Qty To install the extension tablesExtension Tables Main Blade To install the bladeRip Fence and Scale To install the rip fencePage Riving Knife To install the riving knifeSet screws for adjusting riving knife Scoring Blade To install the scoring bladeAligning Blades To install the crosscut tableCrosscut Table To align the blades and riving knifeCrosscut Fence To install the crosscut fenceTo align the rip fence scale with the blade Fence Scale AlignmentTest Run Operations Operation SafetyOperation Tips Please follow these tips Every time you use your sawTo change the blades Changing BladesRip cutting with the sliding table Rip CuttingRip cutting with the rip fence Crosscutting Crosscutting smaller panels Crosscutting using the rip fence as a cut-off gaugeCrosscutting full size panels To perform a miter cut Miter CuttingH3308-SHOP FOX Push Stick AccessoriesG3445-Precision Saw Tool H3771-Blade LocH6460-12 Tooth Scoring Blade Set H1300 H1298 G7984 H2347 H0736Cleaning MaintenanceSchedule Unpainted Cast IronSee Figure LubricationTroubleshooting ServiceSymptom Possible Cause Possible Solution Motor & ElectricalCutting Operations To change the scoring blade arbor flat belt Replacing BeltsTo change the main blade arbor V-belt To calibrate the blade tilt Blade TiltTo square the crosscut fence with the blade Squaring Crosscut Fence to BladeSliding Table Parallelism To adjust the sliding table parallel with the main bladeG0460 Electrical Components G0460 Wiring Diagram G0461 Electrical Components G0461 Wiring Diagram at G0461 Wiring Diagram at Main Body PartsDescription Main Body Parts ListPW01M Flat Washer 8MM Sliding Table Sliding Table Parts List Crosscut Table Crosscut Table Parts List Description Rip Fence Tilt Assembly PK42M Motor AssemblyArbor Assembly Warranty and Returns Comments Warranty CardBOX BELLINGHAM, WA Grizzly INDUSTRIAL, INC