Grizzly G0460/G0461 owner manual Main Blade, To install the blade

Page 24

Main Blade
Components and Hardware Needed:	Qty
Blade 12" (Not Included)	1
Riving Knife	1
To install the blade:

1.DISCONNECT SAW FROM POWER!

2.Open the cabinet and remove the red motor support bolt, shown in Figure 23, by remov- ing the nut and tilting the blade assembly to clear the bolt.

Figure 23. Motor support shipping bolt.

3.Move the blade tilt to 0° (blade 90° to table) and raise the main blade arbor.

4.Slide the table all the way forward to access the blade arbor, loosen the flange bolt secur- ing the lower blade guard, slide the bolt up, and pull open the lower blade guard (see Figure 24).

-22-

Scoring

Blade Arbor

Main Blade

Arbor

Figure 24. Main blade arbor components.

5.Place a hex wrench in the hole in the arbor to prevent the arbor from rotating, then use the arbor wrench to remove the arbor nut and arbor flange.

Note: The arbor nut has left-hand threads and loosens by turning clockwise.

6.Slide the blade onto the arbor with the teeth facing the front of the saw (see Figure 25).

Note: Wear heavy leather gloves to pro- tect your hands when installing or removing blades.

Figure 25. Installing the main blade.

7.Re-install the arbor flange and the arbor nut then tighten them against the blade as shown in Figure 25.

8.Close the lower blade guard and secure it closed with the flange bolt.

G0460/G0461 12" Sliding Table Saw

Image 24

Contents Sliding Table SAW Page Table of Contents Introduction ForewordContact Info Machine Data Sheet G0460/G0461 12 Sliding Table Saw Identification Page Safety Safety Instructions for MachineryAlways Lock Mobile Bases if Used Before Operating Machinery Safety Instructions for Sliding Table Saws Preventing Kickback Protecting Yourself From KickbackTips to reduce the likelihood of kickback Glossary of Terms Circuit Requirements Rewiring to GroundingMagnetic switch Setup Setup Safety UnpackingItems Needed for Setup Description QtyClean Up Inventory Inventory QtyHardware and Tools Lock Washers 8mm Small Wing/TableHardware Recognition Chart Placement Site ConsiderationsMoving & Placing Base Unit Floor LoadMounting to Shop Floor Bolting to Concrete FloorsTo install the extension tables Extension TablesComponents and Hardware Needed Qty To install the blade Main BladeTo install the rip fence Rip Fence and ScalePage To install the riving knife Riving KnifeSet screws for adjusting riving knife To install the scoring blade Scoring BladeTo install the crosscut table Aligning BladesCrosscut Table To align the blades and riving knifeTo install the crosscut fence Crosscut FenceFence Scale Alignment To align the rip fence scale with the bladeTest Run Operation Safety OperationsOperation Tips Please follow these tips Every time you use your sawChanging Blades To change the bladesRip Cutting Rip cutting with the sliding tableRip cutting with the rip fence Crosscutting Crosscutting using the rip fence as a cut-off gauge Crosscutting full size panelsCrosscutting smaller panels Miter Cutting To perform a miter cutAccessories H3308-SHOP FOX Push StickG3445-Precision Saw Tool H3771-Blade LocH1300 H1298 G7984 H2347 H0736 H6460-12 Tooth Scoring Blade SetMaintenance CleaningSchedule Unpainted Cast IronLubrication See FigureService TroubleshootingSymptom Possible Cause Possible Solution Motor & ElectricalCutting Operations Replacing Belts To change the main blade arbor V-beltTo change the scoring blade arbor flat belt Blade Tilt To calibrate the blade tiltSquaring Crosscut Fence to Blade To square the crosscut fence with the bladeTo adjust the sliding table parallel with the main blade Sliding Table ParallelismG0460 Electrical Components G0460 Wiring Diagram G0461 Electrical Components G0461 Wiring Diagram at G0461 Wiring Diagram at Parts Main BodyMain Body Parts List DescriptionPW01M Flat Washer 8MM Sliding Table Sliding Table Parts List Crosscut Table Crosscut Table Parts List Description Rip Fence Tilt Assembly Motor Assembly PK42MArbor Assembly Warranty and Returns Warranty Card CommentsGrizzly INDUSTRIAL, INC BOX BELLINGHAM, WA