Grizzly G0460/G0461 owner manual Safety Instructions for Machinery

Page 9

SECTION 1: SAFETY

For Your Own Safety, Read Instruction Manual Before Operating this Machine

The purpose of safety symbols is to attract your attention to possible hazardous conditions. This manual uses a series of symbols and signal words which are intended to convey the level of importance of the safety messages. The progression of symbols is described below. Remember that safety messages by themselves do not eliminate danger and are not a substitute for proper accident prevention measures.

 

Indicates an imminently hazardous situation which, if not avoided,

 

 

WILL result in death or serious injury.

 

Indicates a potentially hazardous situation which, if not avoided,

 

COULD result in death or serious injury.

 

Indicates a potentially hazardous situation which, if not avoided,

 

MAY result in minor or moderate injury. It may also be used to alert

 

against unsafe practices.

NOTICE

This symbol is used to alert the user to useful information about

proper operation of the machine.

Safety Instructions for Machinery

1.READ THROUGH THE ENTIRE MANUAL BEFORE STARTING MACHINERY. Machinery presents serious injury hazards to untrained users.

2.ALWAYS USE ANSI APPROVED SAFETY GLASSES WHEN OPERATING MACHINERY. Everyday eyeglasses only have impact resistant lenses, they are NOT safety glasses.

3.ALWAYS WEAR AN ANSI APPROVED RESPIRATOR WHEN OPERATING MACHINERY THAT PRODUCES DUST. Wood dust is a carcinogen and can cause cancer and severe respiratory illnesses.

4.ALWAYS USE HEARING PROTECTION WHEN OPERATING MACHINERY. Machinery noise can cause permanent hearing damage.

5.WEAR PROPER APPAREL. DO NOT wear loose clothing, gloves, neckties, rings, or jewelry which may get caught in moving parts. Wear protective hair covering to con- tain long hair and wear non-slip footwear.

6.NEVER OPERATE MACHINERY WHEN TIRED, OR UNDER THE INFLUENCE OF DRUGS OR ALCOHOL. Be mentally alert at all times when running machinery.

G0460/G0461 12" Sliding Table Saw

-7-

Image 9
Contents Sliding Table SAW Page Table of Contents Introduction ForewordContact Info Machine Data Sheet G0460/G0461 12 Sliding Table Saw Identification Page Safety Instructions for Machinery SafetyAlways Lock Mobile Bases if Used Before Operating Machinery Safety Instructions for Sliding Table Saws Preventing Kickback Protecting Yourself From KickbackTips to reduce the likelihood of kickback Glossary of Terms Circuit Requirements Grounding Rewiring toMagnetic switch Setup Safety Unpacking SetupItems Needed for Setup Description QtyInventory Qty Clean Up InventoryLock Washers 8mm Small Wing/Table Hardware and ToolsHardware Recognition Chart Site Considerations PlacementMoving & Placing Base Unit Floor LoadBolting to Concrete Floors Mounting to Shop FloorTo install the extension tables Extension TablesComponents and Hardware Needed Qty Main Blade To install the bladeRip Fence and Scale To install the rip fencePage Riving Knife To install the riving knifeSet screws for adjusting riving knife Scoring Blade To install the scoring bladeAligning Blades To install the crosscut tableCrosscut Table To align the blades and riving knifeCrosscut Fence To install the crosscut fenceTo align the rip fence scale with the blade Fence Scale AlignmentTest Run Operations Operation SafetyOperation Tips Please follow these tips Every time you use your sawTo change the blades Changing BladesRip cutting with the sliding table Rip CuttingRip cutting with the rip fence Crosscutting Crosscutting using the rip fence as a cut-off gauge Crosscutting full size panelsCrosscutting smaller panels To perform a miter cut Miter CuttingH3308-SHOP FOX Push Stick AccessoriesG3445-Precision Saw Tool H3771-Blade LocH6460-12 Tooth Scoring Blade Set H1300 H1298 G7984 H2347 H0736Cleaning MaintenanceSchedule Unpainted Cast IronSee Figure LubricationTroubleshooting ServiceSymptom Possible Cause Possible Solution Motor & ElectricalCutting Operations Replacing Belts To change the main blade arbor V-beltTo change the scoring blade arbor flat belt To calibrate the blade tilt Blade TiltTo square the crosscut fence with the blade Squaring Crosscut Fence to BladeSliding Table Parallelism To adjust the sliding table parallel with the main bladeG0460 Electrical Components G0460 Wiring Diagram G0461 Electrical Components G0461 Wiring Diagram at G0461 Wiring Diagram at Main Body PartsDescription Main Body Parts ListPW01M Flat Washer 8MM Sliding Table Sliding Table Parts List Crosscut Table Crosscut Table Parts List Description Rip Fence Tilt Assembly PK42M Motor AssemblyArbor Assembly Warranty and Returns Comments Warranty CardBOX BELLINGHAM, WA Grizzly INDUSTRIAL, INC