Grizzly G0460/G0461 owner manual Description

Page 63

Crosscut Fence

��

��

��

��

��

��

��

��

��

��

��	��
	��
��	��
��	��
	��

��

��

��

��

��

��

��

						��


		��
		��

REF	PART #	DESCRIPTION

29	PN01M	HEX NUT M6-1
109	P0588109	STOP PLATE
110	P0588110	NYLON PAD
111	P0588111	KNOB M6-1 X 35
112	PW01M	FLAT WASHER 8MM
113	PW03M	FLAT WASHER 6MM
114	P0588114	CLAMPING BASE
115	P0588115	T-NUT M6-1
116	P0588116	CLAMPING ARBOR
117	PW01M	FLAT WASHER 8MM
118	PLN04M	LOCK NUT M8-1.25
119	P0460119	SCALE (LONG)
120	P0460120	CROSSCUT FENCE

REF	PART #	DESCRIPTION

121	PSS04M	SET SCREW M6-1 X 12
122	P0588122	PROTECTION BLOCK
123	P0588123	T-BOLT M10-1.5
124	P0588124	KNOB M10-1.5
124A	P0460124A	KNOB W/SHOULDER
125	P0588125	LOCK PLATE M10-1.5 X 25
126	P0460126	SCALE(SHORT)
127	P0588127	CROSS CUTTING FENCE-SHORT BASE
128	P0588128	LOCK PLATE
129	PSS29M	SET SCREW M6-1 X 35
130	P0588130	CROSS FENCE SUPPORT PLATE
131	PS31M	PHLP HD SCR M6-1 X 35
263	P0460263	SCALE TUBE

G0460/G0461 12" Sliding Table Saw

-61-

Image 63

Contents Sliding Table SAW Page Table of Contents Introduction ForewordContact Info Machine Data Sheet G0460/G0461 12 Sliding Table Saw Identification Page Safety Instructions for Machinery SafetyAlways Lock Mobile Bases if Used Before Operating Machinery Safety Instructions for Sliding Table Saws Preventing Kickback Protecting Yourself From KickbackTips to reduce the likelihood of kickback Glossary of Terms Circuit Requirements Grounding Rewiring toMagnetic switch Description Qty SetupSetup Safety Unpacking Items Needed for SetupInventory Qty Clean Up InventoryLock Washers 8mm Small Wing/Table Hardware and ToolsHardware Recognition Chart Floor Load PlacementSite Considerations Moving & Placing Base UnitBolting to Concrete Floors Mounting to Shop FloorTo install the extension tables Extension TablesComponents and Hardware Needed Qty Main Blade To install the bladeRip Fence and Scale To install the rip fencePage Riving Knife To install the riving knifeSet screws for adjusting riving knife Scoring Blade To install the scoring bladeTo align the blades and riving knife To install the crosscut tableAligning Blades Crosscut TableCrosscut Fence To install the crosscut fenceTo align the rip fence scale with the blade Fence Scale AlignmentTest Run Please follow these tips Every time you use your saw Operation SafetyOperations Operation TipsTo change the blades Changing BladesRip cutting with the sliding table Rip CuttingRip cutting with the rip fence Crosscutting Crosscutting using the rip fence as a cut-off gauge Crosscutting full size panelsCrosscutting smaller panels To perform a miter cut Miter CuttingH3771-Blade Loc AccessoriesH3308-SHOP FOX Push Stick G3445-Precision Saw ToolH6460-12 Tooth Scoring Blade Set H1300 H1298 G7984 H2347 H0736Unpainted Cast Iron MaintenanceCleaning ScheduleSee Figure LubricationMotor & Electrical ServiceTroubleshooting Symptom Possible Cause Possible SolutionCutting Operations Replacing Belts To change the main blade arbor V-beltTo change the scoring blade arbor flat belt To calibrate the blade tilt Blade TiltTo square the crosscut fence with the blade Squaring Crosscut Fence to BladeSliding Table Parallelism To adjust the sliding table parallel with the main bladeG0460 Electrical Components G0460 Wiring Diagram G0461 Electrical Components G0461 Wiring Diagram at G0461 Wiring Diagram at Main Body PartsDescription Main Body Parts ListPW01M Flat Washer 8MM Sliding Table Sliding Table Parts List Crosscut Table Crosscut Table Parts List Description Rip Fence Tilt Assembly PK42M Motor AssemblyArbor Assembly Warranty and Returns Comments Warranty CardBOX BELLINGHAM, WA Grizzly INDUSTRIAL, INC