Grizzly G0460/G0461 owner manual Circuit Requirements

Page 14

SECTION 2: CIRCUIT REQUIREMENTS

Serious personal injury could occur if you connect the machine to the power source before you have completed the setup pro- cess. DO NOT connect the machine to the power source until instructed to do so.

Full Load Amperage Draw

G0460 5 HP 220V 1-Phase	22 Amps
G0461 7.5 HP 220V 3-Phase	20 Amps
G0461 7.5 HP 440V 3-Phase	10 Amps

Circuit Requirements

We recommend connecting your machine to a dedicated and grounded circuit that is rated for the amperage given below. Never replace a circuit breaker on an existing circuit with one of higher amperage without consulting a qualiﬁed electri- cian to ensure compliance with wiring codes. If you are unsure about the wiring codes in your area or you plan to connect your machine to a shared circuit, consult a qualified electrician.

G0460 220V 1-Phase	30 Amp
G0461 220V 3-Phase	30 Amp
G0461 440V 3-Phase	15 Amp

Minimum Cord Requirements

For 220V connection, we recommend using a stranded-copper ﬂexible cord that meets the minimum criteria listed below, does not exceed 50 ft., and has an insulation type that starts with "S." The exact insulation type should account for any exposure to moisture, heat, and oils in the working environment.

G0460 220V 1-Phase	...........10/3 AWG, 300VAC
G0461 220V 3-Phase	...........10/4 AWG, 300VAC
G0461 440V 3-Phase	...... Electrician to Hardwire

-12-

220V Plug/Connection Type

G0460 220V 1-Phase.................................L6-30

G0461 220V 3-Phase............................... L15-30

Figure 4. NEMA L6-30 plug and receptacle.

Figure 5. NEMA L15-30 plug and receptacle.

G0461 440V Connection to Power

Have a qualified electrician hardwire this machine to a dedicated locking shut-off switch that is con- nected to the main power source.

	��	��
	��
		��
	��
		��

Figure 6. Hardwired locking disconnect switch.

G0460/G0461 12" Sliding Table Saw

Image 14

Contents Sliding Table SAW Page Table of Contents Contact Info IntroductionForeword Machine Data Sheet G0460/G0461 12 Sliding Table Saw Identification Page Safety Safety Instructions for MachineryAlways Lock Mobile Bases if Used Before Operating Machinery Safety Instructions for Sliding Table Saws Tips to reduce the likelihood of kickback Preventing KickbackProtecting Yourself From Kickback Glossary of Terms Circuit Requirements Rewiring to GroundingMagnetic switch Items Needed for Setup SetupSetup Safety Unpacking Description QtyClean Up Inventory Inventory QtyHardware and Tools Lock Washers 8mm Small Wing/TableHardware Recognition Chart Moving & Placing Base Unit PlacementSite Considerations Floor LoadMounting to Shop Floor Bolting to Concrete FloorsComponents and Hardware Needed Qty To install the extension tablesExtension Tables To install the blade Main BladeTo install the rip fence Rip Fence and ScalePage To install the riving knife Riving KnifeSet screws for adjusting riving knife To install the scoring blade Scoring BladeCrosscut Table To install the crosscut tableAligning Blades To align the blades and riving knifeTo install the crosscut fence Crosscut FenceFence Scale Alignment To align the rip fence scale with the bladeTest Run Operation Tips Operation SafetyOperations Please follow these tips Every time you use your sawChanging Blades To change the bladesRip Cutting Rip cutting with the sliding tableRip cutting with the rip fence Crosscutting Crosscutting smaller panels Crosscutting using the rip fence as a cut-off gaugeCrosscutting full size panels Miter Cutting To perform a miter cutG3445-Precision Saw Tool AccessoriesH3308-SHOP FOX Push Stick H3771-Blade LocH1300 H1298 G7984 H2347 H0736 H6460-12 Tooth Scoring Blade SetSchedule MaintenanceCleaning Unpainted Cast IronLubrication See FigureSymptom Possible Cause Possible Solution ServiceTroubleshooting Motor & ElectricalCutting Operations To change the scoring blade arbor flat belt Replacing BeltsTo change the main blade arbor V-belt Blade Tilt To calibrate the blade tiltSquaring Crosscut Fence to Blade To square the crosscut fence with the bladeTo adjust the sliding table parallel with the main blade Sliding Table ParallelismG0460 Electrical Components G0460 Wiring Diagram G0461 Electrical Components G0461 Wiring Diagram at G0461 Wiring Diagram at Parts Main BodyMain Body Parts List DescriptionPW01M Flat Washer 8MM Sliding Table Sliding Table Parts List Crosscut Table Crosscut Table Parts List Description Rip Fence Tilt Assembly Motor Assembly PK42MArbor Assembly Warranty and Returns Warranty Card CommentsGrizzly INDUSTRIAL, INC BOX BELLINGHAM, WA