Grizzly G0460/G0461 owner manual Accessories, H3308-SHOP FOX Push Stick, G3445-Precision Saw Tool

Page 41

SECTION 5: ACCESSORIES

H3308—SHOP FOX® Push Stick

Measuring 131⁄2" overall, this push stick allows the operator to keep their hands at a safe distance away from the blade or cutter.

Figure 66. H3308 SHOP FOX® Push Stick.

G3445—Precision Saw Tool

This high impact plastic Saw Aid™ quickly mea- sures blade height and angle and can also serve as a solid push stick. Includes a graduated ruler guide and center finder.

Figure 67. G3445 Precision Saw Tool.

G0460/G0461 12" Sliding Table Saw

H3771—Blade Loc®

This simple tool secures the blade during blade changes, keeping your hands safe and your expensive blade from being damaged.

Figure 68. H3771 Blade Loc®.

G7581—Superbar™

G7582—Master Plate

The miter slot mounted Superbar™ will align, tune and calibrate your tablesaw to within ±0.001 in just minutes. Replace your tablesaw blade when calibrating the double disk ground Master Plate for a precision measurement, with no runout!

Figure 69. Superbar™ and Master Plate.

-39-

Image 41

Contents Sliding Table SAW Page Table of Contents Contact Info IntroductionForeword Machine Data Sheet G0460/G0461 12 Sliding Table Saw Identification Page Safety Instructions for Machinery SafetyAlways Lock Mobile Bases if Used Before Operating Machinery Safety Instructions for Sliding Table Saws Tips to reduce the likelihood of kickback Preventing KickbackProtecting Yourself From Kickback Glossary of Terms Circuit Requirements Grounding Rewiring toMagnetic switch Setup Safety Unpacking SetupItems Needed for Setup Description QtyInventory Qty Clean Up InventoryLock Washers 8mm Small Wing/Table Hardware and ToolsHardware Recognition Chart Site Considerations PlacementMoving & Placing Base Unit Floor LoadBolting to Concrete Floors Mounting to Shop FloorComponents and Hardware Needed Qty To install the extension tablesExtension Tables Main Blade To install the bladeRip Fence and Scale To install the rip fencePage Riving Knife To install the riving knifeSet screws for adjusting riving knife Scoring Blade To install the scoring bladeAligning Blades To install the crosscut tableCrosscut Table To align the blades and riving knifeCrosscut Fence To install the crosscut fenceTo align the rip fence scale with the blade Fence Scale AlignmentTest Run Operations Operation SafetyOperation Tips Please follow these tips Every time you use your sawTo change the blades Changing BladesRip cutting with the sliding table Rip CuttingRip cutting with the rip fence Crosscutting Crosscutting smaller panels Crosscutting using the rip fence as a cut-off gaugeCrosscutting full size panels To perform a miter cut Miter CuttingH3308-SHOP FOX Push Stick AccessoriesG3445-Precision Saw Tool H3771-Blade LocH6460-12 Tooth Scoring Blade Set H1300 H1298 G7984 H2347 H0736Cleaning MaintenanceSchedule Unpainted Cast IronSee Figure LubricationTroubleshooting ServiceSymptom Possible Cause Possible Solution Motor & ElectricalCutting Operations To change the scoring blade arbor flat belt Replacing BeltsTo change the main blade arbor V-belt To calibrate the blade tilt Blade TiltTo square the crosscut fence with the blade Squaring Crosscut Fence to BladeSliding Table Parallelism To adjust the sliding table parallel with the main bladeG0460 Electrical Components G0460 Wiring Diagram G0461 Electrical Components G0461 Wiring Diagram at G0461 Wiring Diagram at Main Body PartsDescription Main Body Parts ListPW01M Flat Washer 8MM Sliding Table Sliding Table Parts List Crosscut Table Crosscut Table Parts List Description Rip Fence Tilt Assembly PK42M Motor AssemblyArbor Assembly Warranty and Returns Comments Warranty CardBOX BELLINGHAM, WA Grizzly INDUSTRIAL, INC