Grizzly G0460/G0461 Site Considerations, Moving & Placing Base Unit, Floor Load, Placement

Page 21

Site Considerations

Floor Load

Most commercial floors are suitable for this machine. Residential floors may require additional reinforcement to support the machine and opera- tor. Refer to the Machine Data Sheet on Page 3 for details about the weight and foot print size.

Placement

Consider existing and anticipated needs, size of material to be processed through your machine, and space for auxiliary stands, work tables or other machinery when establishing a location for your saw. See Figure 16 for the minimum operat- ing clearances of the Model G0460/G0461.

����

����

Figure 16. Operating clearances.

Moving & Placing

Base Unit

Use lifting straps with a 1500 lbs. minimum lifting capacity. If a lifting strap breaks, seri- ous personal injury may occur.

To remove the saw base unit from the crate pallet:

1.Remove the top of the crate and position the forklift forks together and directly above the saw.

2.Place two lifting straps (with hooks on the ends) over the forks and slide the hooks into the points shown in Figure 17.

Figure 17. Lifting the saw base unit.

DO NOT lift the table saw any higher than necessary to clear the floor. Serious per- sonal injury and damage to the machine may occur if safe moving methods are not followed.

3.Lift the saw base unit and move it to your predetermined location.

G0460/G0461 12" Sliding Table Saw

-19-

Image 21
Contents Sliding Table SAW Page Table of Contents Introduction ForewordContact Info Machine Data Sheet G0460/G0461 12 Sliding Table Saw Identification Page Safety Instructions for Machinery SafetyAlways Lock Mobile Bases if Used Before Operating Machinery Safety Instructions for Sliding Table Saws Preventing Kickback Protecting Yourself From KickbackTips to reduce the likelihood of kickback Glossary of Terms Circuit Requirements Grounding Rewiring toMagnetic switch Setup Safety Unpacking SetupItems Needed for Setup Description QtyInventory Qty Clean Up InventoryLock Washers 8mm Small Wing/Table Hardware and ToolsHardware Recognition Chart Site Considerations PlacementMoving & Placing Base Unit Floor LoadBolting to Concrete Floors Mounting to Shop FloorTo install the extension tables Extension TablesComponents and Hardware Needed Qty Main Blade To install the bladeRip Fence and Scale To install the rip fencePage Riving Knife To install the riving knifeSet screws for adjusting riving knife Scoring Blade To install the scoring bladeAligning Blades To install the crosscut tableCrosscut Table To align the blades and riving knifeCrosscut Fence To install the crosscut fenceTo align the rip fence scale with the blade Fence Scale AlignmentTest Run Operations Operation SafetyOperation Tips Please follow these tips Every time you use your sawTo change the blades Changing BladesRip cutting with the sliding table Rip CuttingRip cutting with the rip fence Crosscutting Crosscutting using the rip fence as a cut-off gauge Crosscutting full size panelsCrosscutting smaller panels To perform a miter cut Miter CuttingH3308-SHOP FOX Push Stick AccessoriesG3445-Precision Saw Tool H3771-Blade LocH6460-12 Tooth Scoring Blade Set H1300 H1298 G7984 H2347 H0736Cleaning MaintenanceSchedule Unpainted Cast IronSee Figure LubricationTroubleshooting ServiceSymptom Possible Cause Possible Solution Motor & ElectricalCutting Operations Replacing Belts To change the main blade arbor V-beltTo change the scoring blade arbor flat belt To calibrate the blade tilt Blade TiltTo square the crosscut fence with the blade Squaring Crosscut Fence to BladeSliding Table Parallelism To adjust the sliding table parallel with the main bladeG0460 Electrical Components G0460 Wiring Diagram G0461 Electrical Components G0461 Wiring Diagram at G0461 Wiring Diagram at Main Body PartsDescription Main Body Parts ListPW01M Flat Washer 8MM Sliding Table Sliding Table Parts List Crosscut Table Crosscut Table Parts List Description Rip Fence Tilt Assembly PK42M Motor AssemblyArbor Assembly Warranty and Returns Comments Warranty CardBOX BELLINGHAM, WA Grizzly INDUSTRIAL, INC