Grizzly G0460/G0461 owner manual Riving Knife, To install the riving knife

Page 27

15.Check if the bottom of the rip fence rests on the surface of the table.

Note: The rip fence will scratch the table if the ride height is not adjusted correctly.

—If the rip fence DOES NOT rest on the table, then the fence is correctly adjusted.

—If the rip fence rests on the table, loosen the hex nut shown in Figure 32 and rotate the hex bolt to raise the roller. Tighten the hex nut to lock the height.

Figure 32. Rip fence height adjustment.

G0460/G0461 12" Sliding Table Saw

Riving Knife

To install the riving knife:

1.DISCONNECT SAW FROM POWER!

2.Loosen the riving knife center bolt, slide the riving knife between the plates as shown in Figure 33, and slightly tighten.

Riving Knife

Figure 33. Installing the riving knife.

3.Position the riving knife about 3mm or 18" away from the nearest carbide tooth on the main blade. Note: For a quick gauge, use the 3mm hex wrench to find the correct spacing between the blade and the riving knife, as shown in Figure 34.

Figure 34. Adjusting the riving knife.

4.Tighten the center bolt to secure the riving knife in position.

-25-

Image 27
Contents Sliding Table SAW Page Table of Contents Introduction ForewordContact Info Machine Data Sheet G0460/G0461 12 Sliding Table Saw Identification Page Safety Instructions for Machinery SafetyAlways Lock Mobile Bases if Used Before Operating Machinery Safety Instructions for Sliding Table Saws Preventing Kickback Protecting Yourself From KickbackTips to reduce the likelihood of kickback Glossary of Terms Circuit Requirements Grounding Rewiring toMagnetic switch Description Qty SetupSetup Safety Unpacking Items Needed for SetupInventory Qty Clean Up InventoryLock Washers 8mm Small Wing/Table Hardware and ToolsHardware Recognition Chart Floor Load PlacementSite Considerations Moving & Placing Base UnitBolting to Concrete Floors Mounting to Shop FloorTo install the extension tables Extension TablesComponents and Hardware Needed Qty Main Blade To install the bladeRip Fence and Scale To install the rip fencePage Riving Knife To install the riving knifeSet screws for adjusting riving knife Scoring Blade To install the scoring bladeTo align the blades and riving knife To install the crosscut tableAligning Blades Crosscut TableCrosscut Fence To install the crosscut fenceTo align the rip fence scale with the blade Fence Scale AlignmentTest Run Please follow these tips Every time you use your saw Operation SafetyOperations Operation TipsTo change the blades Changing BladesRip cutting with the sliding table Rip CuttingRip cutting with the rip fence Crosscutting Crosscutting using the rip fence as a cut-off gauge Crosscutting full size panelsCrosscutting smaller panels To perform a miter cut Miter CuttingH3771-Blade Loc AccessoriesH3308-SHOP FOX Push Stick G3445-Precision Saw ToolH6460-12 Tooth Scoring Blade Set H1300 H1298 G7984 H2347 H0736Unpainted Cast Iron MaintenanceCleaning ScheduleSee Figure LubricationMotor & Electrical ServiceTroubleshooting Symptom Possible Cause Possible SolutionCutting Operations Replacing Belts To change the main blade arbor V-beltTo change the scoring blade arbor flat belt To calibrate the blade tilt Blade TiltTo square the crosscut fence with the blade Squaring Crosscut Fence to BladeSliding Table Parallelism To adjust the sliding table parallel with the main bladeG0460 Electrical Components G0460 Wiring Diagram G0461 Electrical Components G0461 Wiring Diagram at G0461 Wiring Diagram at Main Body PartsDescription Main Body Parts ListPW01M Flat Washer 8MM Sliding Table Sliding Table Parts List Crosscut Table Crosscut Table Parts List Description Rip Fence Tilt Assembly PK42M Motor AssemblyArbor Assembly Warranty and Returns Comments Warranty CardBOX BELLINGHAM, WA Grizzly INDUSTRIAL, INC