Grizzly G0460/G0461 owner manual Test Run

Page 33

Test Run

Once the assembly is complete, test run your machine to make sure it runs properly and is ready for regular operation.

The test run consists of verifying the following: 1) The motor powers up and runs correctly and 2) the stop button safety feature works correctly. For the G0461 only, you must also make sure that the motor turns the correct direction.

If, during the test run, you cannot easily locate the source of an unusual noise or vibration, stop using the machine immediately, then review Troubleshooting on Page 43.

If you still cannot remedy a problem, contact our Tech Support at (570) 546-9663 for assistance.

Before starting the saw, make sure you have performed the preceding assembly and adjustment instructions, and you have read through the rest of the manual and are familiar with the various functions and safety features on this machine. Failure to follow this warning could result in serious personal injury or even death!

To test run the machine:

1.Make sure you have read the safety instruc- tions at the beginning of the manual and that the machine is setup properly.

2.Make sure all tools and objects used during setup are cleared away from the machine.

3.Connect the machine to the power source.

4.Push the stop button in, then twist it clock- wise so it pops out.

G0460/G0461 12" Sliding Table Saw

5.Verify that the machine is operating correctly by turning it ON.

—When operating correctly, the machine runs smoothly with little or no vibration or rubbing noises.

—Investigate and correct strange or unusual noises or vibrations before operating the machine further. Always disconnect the machine from power when investigating or correcting potential problems.

6.Turn the machine OFF.

7.Push the STOP button.

8.Press the green ON button. The machine should not start.

—If the machine does not start, the STOP button safety feature is working correctly.

—If the machine does start (with the stop button pushed in), immediately disconnect power to the machine. The STOP button safety feature is not working correctly. This safety feature must work properly before proceeding with regular operations. Call Tech Support for help.

9.FOR G0461 ONLY: Verify that the main blade is turning the correct direction by start- ing the motor, then stopping the motor while watching the main blade come to a stop.

—If the main blade turns clockwise (as stand- ing in front of the machine), it is turning in the correct direction.

—If the main blade turns counterclockwise (toward the rear of the machine), it is turning in the wrong direction. Stop the machine, disconnect it from power, then exchange any two of the three power wires in the terminal box. For additional help with this, contact our Technical Support Department at (570) 546-9663.

-31-

Page 32 Page 34
Image 33
Page 32 Page 34
Contents Sliding Table SAW Page Table of Contents Introduction ForewordContact Info Machine Data Sheet G0460/G0461 12 Sliding Table Saw Identification Page Safety Instructions for Machinery SafetyAlways Lock Mobile Bases if Used Before Operating Machinery Safety Instructions for Sliding Table Saws Preventing Kickback Protecting Yourself From KickbackTips to reduce the likelihood of kickback Glossary of Terms Circuit Requirements Grounding Rewiring toMagnetic switch Setup Safety Unpacking SetupItems Needed for Setup Description QtyInventory Qty Clean Up InventoryLock Washers 8mm Small Wing/Table Hardware and ToolsHardware Recognition Chart Site Considerations PlacementMoving & Placing Base Unit Floor LoadBolting to Concrete Floors Mounting to Shop FloorTo install the extension tables Extension TablesComponents and Hardware Needed Qty Main Blade To install the bladeRip Fence and Scale To install the rip fencePage Riving Knife To install the riving knifeSet screws for adjusting riving knife Scoring Blade To install the scoring bladeAligning Blades To install the crosscut tableCrosscut Table To align the blades and riving knifeCrosscut Fence To install the crosscut fenceTo align the rip fence scale with the blade Fence Scale AlignmentTest Run Operations Operation SafetyOperation Tips Please follow these tips Every time you use your sawTo change the blades Changing BladesRip cutting with the sliding table Rip CuttingRip cutting with the rip fence Crosscutting Crosscutting using the rip fence as a cut-off gauge Crosscutting full size panelsCrosscutting smaller panels To perform a miter cut Miter CuttingH3308-SHOP FOX Push Stick AccessoriesG3445-Precision Saw Tool H3771-Blade LocH6460-12 Tooth Scoring Blade Set H1300 H1298 G7984 H2347 H0736Cleaning MaintenanceSchedule Unpainted Cast IronSee Figure LubricationTroubleshooting ServiceSymptom Possible Cause Possible Solution Motor & ElectricalCutting Operations Replacing Belts To change the main blade arbor V-beltTo change the scoring blade arbor flat belt To calibrate the blade tilt Blade TiltTo square the crosscut fence with the blade Squaring Crosscut Fence to BladeSliding Table Parallelism To adjust the sliding table parallel with the main bladeG0460 Electrical Components G0460 Wiring Diagram G0461 Electrical Components G0461 Wiring Diagram at G0461 Wiring Diagram at Main Body PartsDescription Main Body Parts ListPW01M Flat Washer 8MM Sliding Table Sliding Table Parts List Crosscut Table Crosscut Table Parts List Description Rip Fence Tilt Assembly PK42M Motor AssemblyArbor Assembly Warranty and Returns Comments Warranty CardBOX BELLINGHAM, WA Grizzly INDUSTRIAL, INC
Top Page Image Contents