Woodstock W1747 owner manual Electrical, 220V Operation, Extension Cords, Grounding

Page 11

W1747 20" Planer

ELECTRICAL

220V Operation

The Model W1747 operates at 220V. Always connect this machine to a dedicated circuit with a verified ground, using the recommended circuit size listed at the bottom of this page.

Never replace a circuit breaker with one of higher amper- age without consulting a qualified electrician to ensure compliance with wiring codes. If you are unsure about the wiring codes in your area or plan to connect your machine to a shared circuit, you may create a fire haz- ard—consult a qualified electrician to reduce this risk.

Extension Cords

We do not recommend using an extension cord for 220V operation. Instead, hard wire the machine directly to a power panel that is equipped with a manual shutoff lever lever and that can be locked in the OFF position.

Grounding

This machine must be grounded! Hardwire this machine into a power supply circuit that contains a ground cir- cuit. If you have any questions about correct electrical installation, contact a qualified electrician for assistance to make sure all connections are safe and adhere to required electrical codes.

Electrocution or severe shock could occur if machine is not grounded.

Replacing an existing circuit breaker with one rated for higher amperage may result in a fire. Get help from an electrician if your circuit will be over- loaded by the machine.

TURN OFF and LOCK your master power switch so no power is available to the planer before connecting electrical OFF wires! If you ignore this warning serious electrical shock may occur, causing injury or

death!

ELECTRICAL

Operating Voltage	Amp Draw	Min. Circuit Size	Plug/Receptacle	Extension Cord

220V Operation	30 Amps	40A	Hardwire	Not Recommended

-9-

Image 11

Contents Planer Page Contents Service Woodstock Technical Support IntroductionSpecifications Controls and Features Standard Safety Instructions SafetyAlways Lock Mobile Bases if Used Before Operating Machinery Additional Safety Instructions for Planers Grounding Electrical220V Operation Extension CordsInventory SET UPItems Needed for Set Up UnpackingHardware and Tools Machine PlacementLifting Planer These items are coated and must be cleaned Cleaning MachineExtension wing fasteners Leveling controls Extension WingsDust Hood To install the handwheel, do these stepsHandwheel To check the gearbox oil level, do these steps Connecting to PowerKnife Setting Gauge Gearbox Oil LevelTo perform a test run, do these steps Recommended AdjustmentsTest Run Tighten V-BeltsBasic steps of operating the planer are as follows OperationsGeneral Basic OperationOperation Tips Feed control knob positions Feed SpeedBed Rollers Adjustment Height Range 002-0.020To adjust the bed rollers, do these steps Planer Accessories AccessoriesOFF Maintenance Schedule MaintenanceCleaning Belts To adjust/replace the V-belts, do these stepsLubrication To inspect the knives, do these steps ServiceInspecting Knives To set the knives, do these steps Setting/Replacing KnivesChain Tension To adjust the chain tension, do these stepsMaximum Allowable Tolerances Table ParallelismTable micro-adjustment screws To adjust the table parallelism, do these stepsDistance Below Knife Edge at *BDC Rollers, Chip Breaker Pressure Bar Heights27, 28, Roller height adjustmentService Spring Tension To adjust roller spring tension, do these stepsTo calibrate the scale, do these steps Chip Deflector Gap SettingTo adjust the deflector position, do these steps Scale CalibrationAnti-kickback fingers Anti-Kickback FingersChecking belt alignment Pulley AlignmentW1747 motor junction box W1747 Electrical ComponentsW1747 Wiring Diagram Moving parts have come to a complete stop TroubleshootingCutting Headstock Assembly Parts Breakdown PART# Description Headstock Assembly Parts ListXPN09M Table, Base, and Columns Parts Breakdown Table, Base, and Columns Parts List Stand/Motor Assembly Parts Breakdown Stand/Motor Assembly Parts List Parts Warranty Comments Warranty RegistrationBOX BELLINGHAM, WA