Woodstock W1747 owner manual Machine Placement, Lifting Planer, Hardware and Tools

Page 13

W1747 20" Planer

Hardware and Tools

 

• Hex Wrenches 3, 4, 5, 6mm

4

• Wrenches 8/10, 12/14, 17/19mm

3

• Set Screws M8-1.25 x 20 (Wings)

6

• Hex Bolts M8-1.25 x 25 (Wings)

6

•

Handwheel Bushing (Handwheel)

1

•

Handwheel Handle (Handwheel)

1

• Hex Nut M12-1.75 (Handwheel)

1

• Flat Washer 12mm (Handwheel)

1

• Key 4 x 4 x 10mm (Handwheel)

1

• Cap Screws M6-1 x 12 (Dust Hood)

6

• Flat Washers 6mm (Dust Hood)

6

If any parts are missing, examine the packaging for the missing parts. For any missing parts, find the part num- ber in the back of this manual and contact Woodstock International, Inc. at (360) 734-3482 or at tech- support@shopfox.biz

MAKE your shop “child safe." Ensure that your workplace is inaccessible to youngsters by closing and locking all entrances when you are away. NEVER allow untrained visitors in your shop when assembling, adjusting or operat- ing equipment.

Machine Placement

•Floor Load: This machine distributes a heavy load in a small footprint. Some floors may require additional bracing to support both machine and operator.

•Working Clearances: Consider existing and anticipated needs, size of material to be processed through the machine, and space for auxiliary stands, work tables or other machinery when establishing a location for your planer.

•Lighting: Lighting should be bright enough to eliminate shadow and prevent eye strain.

Lifting Planer

The cabinet stand on the Model W1747 is equipped with lifting bars (see Page 5) to lift and place the planer.

When lifting the planer with a forklift, we recommend placing shop rags or cardboard between the forks and cabinet base so you do not scratch the paint.

Figure 3 shows an example of a typical planer with lifting bars being lifted correctly with a forklift.

USE power lifting equipment to lift this planer. Otherwise, seri- ous personal injury may occur.

-11-

Figure 3. Example of planer being lifted

using forklift.

SET UP

Page 12 Page 14
Image 13
Page 12 Page 14
Contents Planer Page Contents Service Woodstock Technical Support IntroductionSpecifications Controls and Features Standard Safety Instructions SafetyAlways Lock Mobile Bases if Used Before Operating Machinery Additional Safety Instructions for Planers 220V Operation ElectricalExtension Cords GroundingItems Needed for Set Up SET UPUnpacking InventoryLifting Planer Machine PlacementHardware and Tools These items are coated and must be cleaned Cleaning MachineExtension wing fasteners Leveling controls Extension WingsHandwheel To install the handwheel, do these stepsDust Hood Knife Setting Gauge Connecting to PowerGearbox Oil Level To check the gearbox oil level, do these stepsTest Run Recommended AdjustmentsTighten V-Belts To perform a test run, do these stepsGeneral OperationsBasic Operation Basic steps of operating the planer are as followsOperation Tips Feed control knob positions Feed SpeedTo adjust the bed rollers, do these steps Adjustment Height Range 002-0.020Bed Rollers Planer Accessories AccessoriesOFF Cleaning MaintenanceMaintenance Schedule Belts To adjust/replace the V-belts, do these stepsLubrication Inspecting Knives ServiceTo inspect the knives, do these steps To set the knives, do these steps Setting/Replacing KnivesChain Tension To adjust the chain tension, do these stepsMaximum Allowable Tolerances Table ParallelismTable micro-adjustment screws To adjust the table parallelism, do these stepsDistance Below Knife Edge at *BDC Rollers, Chip Breaker Pressure Bar Heights27, 28, Roller height adjustmentService Spring Tension To adjust roller spring tension, do these stepsTo adjust the deflector position, do these steps Chip Deflector Gap SettingScale Calibration To calibrate the scale, do these stepsAnti-kickback fingers Anti-Kickback FingersChecking belt alignment Pulley AlignmentW1747 motor junction box W1747 Electrical ComponentsW1747 Wiring Diagram Moving parts have come to a complete stop TroubleshootingCutting Headstock Assembly Parts Breakdown PART# Description Headstock Assembly Parts ListXPN09M Table, Base, and Columns Parts Breakdown Table, Base, and Columns Parts List Stand/Motor Assembly Parts Breakdown Stand/Motor Assembly Parts List Parts Warranty Comments Warranty RegistrationBOX BELLINGHAM, WA
Top Page Image Contents