Woodstock W1747 owner manual Unpacking, Items Needed for Set Up, Inventory

Page 12

W1747 20" Planer

SET UP

SET UP

Unpacking

The SHOP FOX® Model W1747 has been carefully pack- aged for safe transporting. If you notice the machine has been damaged, please contact your authorized SHOP FOX® dealer immediately.

Items Needed for Set Up

The following items are needed, but not included, to setup your machine:

• Safety Glasses (for each person)		........................1
•	Solvent Cleaner	1
• Shop Rags for Cleaning		As Needed
• Extra Person for Lifting Help		1
•	Fork Lift	1
• Straightedge (see Page 13)		1
•	Phillips Screwdriver #2	1

Inventory

The following is a description of the main components shipped with the SHOP FOX® Model W1747. Lay the com- ponents out to inventory them.

Note: Some parts and hardware may already be installed on the machine. Make sure to check the machine when you use this inventory list.

Box Inventory (Figure 2)		Qty
A.	Planer Unit	1
B.	Knife Gauge Assembly	1
C.	Dust Hood	2
D.	Handwheel	1
E.	Table Extension Wings	1

SUFFOCATION HAZARD!

Immediately discard all

plastic bags and pack-

ing materials to elimi-

nate choking/suffocation

hazards for children and

animals.

TURN OFF and LOCK your master power switch so no power is available to the planer before you do any assembly OFF or adjustment tasks. If you ignore this warning serious electrical shock may occur, causing

injury or death!

A

E

B	C	D

Figure 2. Planer box inventory.

-10-

Image 12

Contents Planer Page Contents Service Introduction Woodstock Technical SupportSpecifications Controls and Features Safety Standard Safety InstructionsAlways Lock Mobile Bases if Used Before Operating Machinery Additional Safety Instructions for Planers Electrical 220V OperationExtension Cords GroundingSET UP Items Needed for Set UpUnpacking InventoryMachine Placement Lifting PlanerHardware and Tools Cleaning Machine These items are coated and must be cleanedExtension Wings Extension wing fasteners Leveling controlsTo install the handwheel, do these steps HandwheelDust Hood Connecting to Power Knife Setting GaugeGearbox Oil Level To check the gearbox oil level, do these stepsRecommended Adjustments Test RunTighten V-Belts To perform a test run, do these stepsOperations GeneralBasic Operation Basic steps of operating the planer are as followsOperation Tips Feed Speed Feed control knob positionsAdjustment Height Range 002-0.020 To adjust the bed rollers, do these stepsBed Rollers Accessories Planer AccessoriesOFF Maintenance CleaningMaintenance Schedule To adjust/replace the V-belts, do these steps BeltsLubrication Service Inspecting KnivesTo inspect the knives, do these steps Setting/Replacing Knives To set the knives, do these stepsTo adjust the chain tension, do these steps Chain TensionTable Parallelism Maximum Allowable TolerancesTo adjust the table parallelism, do these steps Table micro-adjustment screwsRollers, Chip Breaker Pressure Bar Heights Distance Below Knife Edge at *BDCRoller height adjustment 27, 28,Service To adjust roller spring tension, do these steps Spring TensionChip Deflector Gap Setting To adjust the deflector position, do these stepsScale Calibration To calibrate the scale, do these stepsAnti-Kickback Fingers Anti-kickback fingersPulley Alignment Checking belt alignmentW1747 Electrical Components W1747 motor junction boxW1747 Wiring Diagram Troubleshooting Moving parts have come to a complete stopCutting Headstock Assembly Parts Breakdown Headstock Assembly Parts List PART# DescriptionXPN09M Table, Base, and Columns Parts Breakdown Table, Base, and Columns Parts List Stand/Motor Assembly Parts Breakdown Stand/Motor Assembly Parts List Parts Warranty Warranty Registration CommentsBOX BELLINGHAM, WA