Woodstock W1747 owner manual Service

Page 35

W1747 20" Planer

To adjust the height of the infeed and outfeed rollers, chip breaker and pressure bar using wood blocks and a feeler gauge, do these steps:

1.Build the wood blocks by cutting a straight 6' long 2x4 in half.

Note: Having the wood blocks at an even height is critical to the accuracy of your overall adjustments. For best results, remove board warpage by squaring the 2x4 with a jointer and table saw before cutting in half.

2.DISCONNECT THE PLANER FROM THE POWER SOURCE!

3.Lower the bed rollers below the table.

4.Place one wood block along the left side of the table, and place the other wood block along the right side of the table, as illustrated in Figure 30.

���

Figure 30. Wood blocks on table.

5.Remove the dust port, top cover, and belt cover.

6.Adjust the table and use the feeler gauge until you have a 0.040" gap between the edge of a knife at bottom dead center (find by rocking cutterhead pul- ley) and the wood blocks.

7.Lock the table height in place, as the wood blocks will now be your reference points for the rest of the adjustments.

8.Loosen the infeed roller adjustment jam nuts (Figure 32) and turn the adjustment set screws on each end to raise the feed roller above the wood block (if nec- essary), then bring it back down so it just touches the wood block on both sides.

9.Lock the infeed roller adjustment set screws in place with the jam nuts, making sure they do not move while tightening.

10.Without moving the table, adjust the chip breaker (Figure 29), pressure bar (Figure 28), and outfeed roller (Figure 27) in the same manner, using the wood blocks as your reference point.

11.When you are finished with the adjustments, replace the top cover, dust port, and belt cover.

-33-

SERVICE

Page 34 Page 36
Image 35
Page 34 Page 36
Contents Planer Page Contents Service Woodstock Technical Support IntroductionSpecifications Controls and Features Standard Safety Instructions SafetyAlways Lock Mobile Bases if Used Before Operating Machinery Additional Safety Instructions for Planers Grounding Electrical220V Operation Extension CordsInventory SET UPItems Needed for Set Up UnpackingHardware and Tools Machine PlacementLifting Planer These items are coated and must be cleaned Cleaning MachineExtension wing fasteners Leveling controls Extension WingsDust Hood To install the handwheel, do these stepsHandwheel To check the gearbox oil level, do these steps Connecting to PowerKnife Setting Gauge Gearbox Oil LevelTo perform a test run, do these steps Recommended AdjustmentsTest Run Tighten V-BeltsBasic steps of operating the planer are as follows OperationsGeneral Basic OperationOperation Tips Feed control knob positions Feed SpeedBed Rollers Adjustment Height Range 002-0.020To adjust the bed rollers, do these steps Planer Accessories AccessoriesOFF Maintenance Schedule MaintenanceCleaning Belts To adjust/replace the V-belts, do these stepsLubrication To inspect the knives, do these steps ServiceInspecting Knives To set the knives, do these steps Setting/Replacing KnivesChain Tension To adjust the chain tension, do these stepsMaximum Allowable Tolerances Table Parallelism Table micro-adjustment screws To adjust the table parallelism, do these stepsDistance Below Knife Edge at *BDC Rollers, Chip Breaker Pressure Bar Heights27, 28, Roller height adjustmentService Spring Tension To adjust roller spring tension, do these stepsTo calibrate the scale, do these steps Chip Deflector Gap SettingTo adjust the deflector position, do these steps Scale CalibrationAnti-kickback fingers Anti-Kickback FingersChecking belt alignment Pulley AlignmentW1747 motor junction box W1747 Electrical ComponentsW1747 Wiring Diagram Moving parts have come to a complete stop TroubleshootingCutting Headstock Assembly Parts Breakdown PART# Description Headstock Assembly Parts ListXPN09M Table, Base, and Columns Parts Breakdown Table, Base, and Columns Parts List Stand/Motor Assembly Parts Breakdown Stand/Motor Assembly Parts List Parts Warranty Comments Warranty RegistrationBOX BELLINGHAM, WA
Top Page Image Contents