Woodstock W1747 owner manual Lubrication

Page 27

W1747 20" Planer

Lubrication

This planer uses sealed and pre-lubricated ball bearings that require no lubrication.

The following is a list of parts that need lubrication:

Columns/Lead Screws: The four columns should be lubri- cated weekly with SAE 30W oil. Unfasten dust covers to gain access. The four lead screws (Figure 14) should be lubricated with general purpose grease once a month.

Worm Gear: The worm gear should be inspected monthly and lubricated with general purpose grease when need- ed. Remove the worm gear box to inspect. See parts dia- gram on Page 44 for location.

Chain: The table height adjustment chain (see Figure 21 on Page 28) should be inspected monthly and lubricated with general purpose grease when needed.

Gear Box: Gear box oil should be changed after the first 20 hours of operation (see Figure 15). Inspect levels periodically and change yearly. Replace gear oil more fre- quently under heavy use. See Page 15 for instructions on adding oil.

Replace with 80W-90W gear oil. Fill until oil reaches the top of the filler plug port for correct oil level.

Drive Chain: The drive chain should be inspected and lubricated monthly. Check sprocket, chain and cotter pin during inspection. Use a general purpose grease. Some chains will have master links instead of cotter pins.

Feed Rollers: Regular lubrication of feed rollers is crucial to the operation of your planer. Lubricate every 30 hours of use. Each end of each power feed roller has an oiling port located on the top of the headstock (Figure 16). Apply SAE 30W oil, making sure that the lubricant pen- etrates the bearing.

 

SHOCK HAZARD!

 

 

Always disconnect power to the

OFF

machine before lubricating! Failure to

do this may result in serious personal

 

injury!

 

 

-25-

Column

Lead screw

 

Figure 14. Columns and lead screws

(Shown with cover removed).

OFF

Fill Plug

Drain Plug

Figure 15. Gearbox oil drain/fill locations.

Oil

Figure 16. Feed roller lubrication

locations.

MAINTENANCE

Page 26 Page 28
Image 27
Page 26 Page 28
Contents Planer Page Contents Service Woodstock Technical Support IntroductionSpecifications Controls and Features Standard Safety Instructions SafetyAlways Lock Mobile Bases if Used Before Operating Machinery Additional Safety Instructions for Planers Grounding Electrical220V Operation Extension CordsInventory SET UPItems Needed for Set Up UnpackingMachine Placement Lifting PlanerHardware and Tools These items are coated and must be cleaned Cleaning MachineExtension wing fasteners Leveling controls Extension WingsTo install the handwheel, do these steps HandwheelDust Hood To check the gearbox oil level, do these steps Connecting to PowerKnife Setting Gauge Gearbox Oil LevelTo perform a test run, do these steps Recommended AdjustmentsTest Run Tighten V-BeltsBasic steps of operating the planer are as follows OperationsGeneral Basic OperationOperation Tips Feed control knob positions Feed SpeedAdjustment Height Range 002-0.020 To adjust the bed rollers, do these stepsBed Rollers Planer Accessories AccessoriesOFF Maintenance CleaningMaintenance Schedule Belts To adjust/replace the V-belts, do these stepsLubrication Service Inspecting KnivesTo inspect the knives, do these steps To set the knives, do these steps Setting/Replacing KnivesChain Tension To adjust the chain tension, do these stepsMaximum Allowable Tolerances Table ParallelismTable micro-adjustment screws To adjust the table parallelism, do these stepsDistance Below Knife Edge at *BDC Rollers, Chip Breaker Pressure Bar Heights27, 28, Roller height adjustmentService Spring Tension To adjust roller spring tension, do these stepsTo calibrate the scale, do these steps Chip Deflector Gap SettingTo adjust the deflector position, do these steps Scale CalibrationAnti-kickback fingers Anti-Kickback FingersChecking belt alignment Pulley AlignmentW1747 motor junction box W1747 Electrical ComponentsW1747 Wiring Diagram Moving parts have come to a complete stop TroubleshootingCutting Headstock Assembly Parts Breakdown PART# Description Headstock Assembly Parts ListXPN09M Table, Base, and Columns Parts Breakdown Table, Base, and Columns Parts List Stand/Motor Assembly Parts Breakdown Stand/Motor Assembly Parts List Parts Warranty Comments Warranty RegistrationBOX BELLINGHAM, WA
Top Page Image Contents