Woodstock W1747 owner manual Parts

Page 51

W1747 20" Planer

Warning Label Placement and Parts List

Safety labels warn about machine hazards and how to prevent machine damage or injury. The owner of this machine MUST maintain the original location and readability of all labels on this machine. If any label is removed or becomes unreadable, REPLACE that label before allowing the machine to enter service again. Contact Woodstock International, Inc. at (360) 734-3482 or www. shopfoxtools.com to order new labels.

333

324	330	329	331
324

323

322

321

	335
320	334

336

328	332	327	325	326

325

REF	PART�#	DESCRIPTION		REF	PART�#	DESCRIPTION
320	X1747320	MODEL�NUMBER�LABEL		329	X1747329	MACHINE�ID�LABEL
321	XLABEL-15	EAR�PROTECTION�LABEL		330	XLABEL-08	READ�MANUAL�LABEL
322	X1747322	RESPIRATOR�LABEL		331	XLABEL-01	SAFETY�GLASSES�LABEL
323	XLABEL-04	ELECTRICITY�LABEL		332	X1747332	SHUT�COVER�WARNING�LABEL
324	X1747324	CONTROL�PANEL�LABEL		333	X1747333	SPEED�CHANGE�LABEL
325	X1747325	LUBRICATION�LABEL		334	X1747334	SHOP�FOX�LOGO�PLATE	PARTS
326	X1747326	ADJUST�SCREW�LABEL		335	XPAINTSF701	PAINT�FOR�SHOP�FOX�MACHINES
327	X1747327	CUTTERHEAD�WARNING�LABEL		336	X1747336	DECORATIVE�STRIPE�TAPE
328	X1747328	UNPLUG�POWER�220V�LABEL
			-49-

Image 51

Contents Planer Page Contents Service Woodstock Technical Support IntroductionSpecifications Controls and Features Standard Safety Instructions SafetyAlways Lock Mobile Bases if Used Before Operating Machinery Additional Safety Instructions for Planers Grounding Electrical220V Operation Extension CordsInventory SET UPItems Needed for Set Up UnpackingMachine Placement Lifting PlanerHardware and Tools These items are coated and must be cleaned Cleaning MachineExtension wing fasteners Leveling controls Extension WingsTo install the handwheel, do these steps HandwheelDust Hood To check the gearbox oil level, do these steps Connecting to PowerKnife Setting Gauge Gearbox Oil LevelTo perform a test run, do these steps Recommended AdjustmentsTest Run Tighten V-BeltsBasic steps of operating the planer are as follows OperationsGeneral Basic OperationOperation Tips Feed control knob positions Feed SpeedAdjustment Height Range 002-0.020 To adjust the bed rollers, do these stepsBed Rollers Planer Accessories AccessoriesOFF Maintenance CleaningMaintenance Schedule Belts To adjust/replace the V-belts, do these stepsLubrication Service Inspecting KnivesTo inspect the knives, do these steps To set the knives, do these steps Setting/Replacing KnivesChain Tension To adjust the chain tension, do these stepsMaximum Allowable Tolerances Table ParallelismTable micro-adjustment screws To adjust the table parallelism, do these stepsDistance Below Knife Edge at *BDC Rollers, Chip Breaker Pressure Bar Heights27, 28, Roller height adjustmentService Spring Tension To adjust roller spring tension, do these stepsTo calibrate the scale, do these steps Chip Deflector Gap SettingTo adjust the deflector position, do these steps Scale CalibrationAnti-kickback fingers Anti-Kickback FingersChecking belt alignment Pulley AlignmentW1747 motor junction box W1747 Electrical ComponentsW1747 Wiring Diagram Moving parts have come to a complete stop TroubleshootingCutting Headstock Assembly Parts Breakdown PART# Description Headstock Assembly Parts ListXPN09M Table, Base, and Columns Parts Breakdown Table, Base, and Columns Parts List Stand/Motor Assembly Parts Breakdown Stand/Motor Assembly Parts List Parts Warranty Comments Warranty RegistrationBOX BELLINGHAM, WA