Woodstock W1747 owner manual Specifications

Page 6

INTRODUCTION

	W1747 20" Planer



Specifications
Motor:
Type	TEFC Capacitor-Start Induction
Horsepower	5 HP
Phase / Voltage	Single-Phase / 220V
Amps	30
Cycle / RPM	60 Hertz / 3450 RPM
Switch	Magnetic with Thermal Overload Relay
Power Transfer	Triple V-Belt Drive
Bearings	Shielded & Lubricated Ball Bearings
Capacity:
Maximum Depth of Cut	1/8"
Maximum Width of Cut	20"
Maximum Cutting Height	8"
Minimum Stock Thickness	1/4"
Minimum Stock Length	7"
Cutterhead Diameter	35/32''
Cutterhead Speed	5,500 RPM
Cuts per Minute	22,000
Feed Rates	18 FPM & 23 FPM
Cuts Per Inch (Effective)	25 & 20
Overall Dimensions:
Table Size	253/4" x 20"
Height	43"
Overall Depth	56"
Overall Width	411/2"
Shipping Weight	910 lbs.
Net Weight	810 lbs.
Base Dimensions	271/2" L x 23" W x 133/4" H
Crate Size	291/2" L x 433/8" W x 461/4" H
Footprint	25" x 281/2"
Construction:
Table	Precision-Ground Cast Iron
Infeed Roller	Spiral Serrated / Steel
Outfeed Roller	Steel
Stand	Formed Steel
Cutterhead	4 Knife
Knife Size	201/16" L x 1" W x 1/8" H
Knife Adjustment	Springs and Jack Screws

Features:

...............................................Cast Iron Extension Tables

...........................................................Two Table Locks

................................................................ 5" Dust Port

...................................... Inch & Metric Measurement Scale

................................................. 2 Adjustable Bed Rollers

......................................................Board Return Rollers

-4-

Image 6

Contents Planer Page Contents Service Introduction Woodstock Technical SupportSpecifications Controls and Features Safety Standard Safety InstructionsAlways Lock Mobile Bases if Used Before Operating Machinery Additional Safety Instructions for Planers Extension Cords Electrical220V Operation GroundingUnpacking SET UPItems Needed for Set Up InventoryMachine Placement Lifting PlanerHardware and Tools Cleaning Machine These items are coated and must be cleanedExtension Wings Extension wing fasteners Leveling controlsTo install the handwheel, do these steps HandwheelDust Hood Gearbox Oil Level Connecting to PowerKnife Setting Gauge To check the gearbox oil level, do these stepsTighten V-Belts Recommended AdjustmentsTest Run To perform a test run, do these stepsBasic Operation OperationsGeneral Basic steps of operating the planer are as followsOperation Tips Feed Speed Feed control knob positionsAdjustment Height Range 002-0.020 To adjust the bed rollers, do these stepsBed Rollers Accessories Planer AccessoriesOFF Maintenance CleaningMaintenance Schedule To adjust/replace the V-belts, do these steps BeltsLubrication Service Inspecting KnivesTo inspect the knives, do these steps Setting/Replacing Knives To set the knives, do these stepsTo adjust the chain tension, do these steps Chain TensionTable Parallelism Maximum Allowable TolerancesTo adjust the table parallelism, do these steps Table micro-adjustment screwsRollers, Chip Breaker Pressure Bar Heights Distance Below Knife Edge at *BDCRoller height adjustment 27, 28,Service To adjust roller spring tension, do these steps Spring TensionScale Calibration Chip Deflector Gap SettingTo adjust the deflector position, do these steps To calibrate the scale, do these stepsAnti-Kickback Fingers Anti-kickback fingersPulley Alignment Checking belt alignmentW1747 Electrical Components W1747 motor junction boxW1747 Wiring Diagram Troubleshooting Moving parts have come to a complete stopCutting Headstock Assembly Parts Breakdown Headstock Assembly Parts List PART# DescriptionXPN09M Table, Base, and Columns Parts Breakdown Table, Base, and Columns Parts List Stand/Motor Assembly Parts Breakdown Stand/Motor Assembly Parts List Parts Warranty Warranty Registration CommentsBOX BELLINGHAM, WA