Woodstock W1747 owner manual Chain Tension, To adjust the chain tension, do these steps

Page 30
-28-

W1747 20" Planer

6.Position the knife gauge over the knife as shown in Figure 17 and loosen the gib bolts until the knife is completely loose.

7.Jack Screws—Using a 3mm hex wrench, find the jack screws through the access holes in the cutterhead (Figure 19) and rotate the jack screws to raise or lower the knife. When the knife is set correctly, it will barely touch the middle pad of the knife setting gauge. Snug the gib bolts tight enough to just hold the knife in place. Repeat Steps 5-7with the rest of the knives.

Springs—Push the knife down with the gauge so that the knife edge touches the middle pad of the gauge. Hold the gauge down and tighten the gib bolts just tight enough to hold the knife in place. Repeat Steps 5-7with the rest of the knives.

8.Rotate the cutterhead to the first knife you started with. Slightly tighten all the gib bolts by following the tightening sequence shown in Figure 20. Repeat this step on the rest of the knives.

9.Final tighten each gib bolt, then reinstall the top cover, dust port and bolt guard.

OFF

Figure 19. Jack screw access hole.

5

3

1

2

4

6

Figure 20. Gib bolt tigthening sequence.

SERVICE

Chain Tension

The chain drive transfers movement from the handwheel to elevate the table. The chain drive can be adjusted to remove slack if the chain stretches over time or is loos- ened during table leveling procedures.

To adjust the chain tension, do these steps:

1.DISCONNECT THE PLANER FROM THE POWER SOURCE!

2.Remove the motor access panel.

NOTICE

During the next step, DO NOT let the chain fall off the sprockets—returning it to its proper location without changing the table adjustments will be very difficult and time consuming.

3.Loosen the two lock bolts, move the idler sprocket against the chain to tighten it (Figure 21) and re- tighten the locking bolts.

4.Check chain lubrication. Refer to MAINTENANCE on

Page 23 for further details.

Idler Sprocket

Table Height

Adjustment

Chain

Lock Bolts

Figure 21. Underside of table.

Page 29 Page 31
Image 30
Page 29 Page 31
Contents Planer Page Contents Service Introduction Woodstock Technical SupportSpecifications Controls and Features Safety Standard Safety InstructionsAlways Lock Mobile Bases if Used Before Operating Machinery Additional Safety Instructions for Planers Extension Cords Electrical220V Operation GroundingUnpacking SET UPItems Needed for Set Up InventoryMachine Placement Lifting PlanerHardware and Tools Cleaning Machine These items are coated and must be cleanedExtension Wings Extension wing fasteners Leveling controlsTo install the handwheel, do these steps HandwheelDust Hood Gearbox Oil Level Connecting to PowerKnife Setting Gauge To check the gearbox oil level, do these stepsTighten V-Belts Recommended AdjustmentsTest Run To perform a test run, do these stepsBasic Operation OperationsGeneral Basic steps of operating the planer are as followsOperation Tips Feed Speed Feed control knob positionsAdjustment Height Range 002-0.020 To adjust the bed rollers, do these stepsBed Rollers Accessories Planer AccessoriesOFF Maintenance CleaningMaintenance Schedule To adjust/replace the V-belts, do these steps BeltsLubrication Service Inspecting KnivesTo inspect the knives, do these steps Setting/Replacing Knives To set the knives, do these stepsTo adjust the chain tension, do these steps Chain TensionTable Parallelism Maximum Allowable TolerancesTo adjust the table parallelism, do these steps Table micro-adjustment screwsRollers, Chip Breaker Pressure Bar Heights Distance Below Knife Edge at *BDCRoller height adjustment 27, 28,Service To adjust roller spring tension, do these steps Spring TensionScale Calibration Chip Deflector Gap SettingTo adjust the deflector position, do these steps To calibrate the scale, do these stepsAnti-Kickback Fingers Anti-kickback fingersPulley Alignment Checking belt alignmentW1747 Electrical Components W1747 motor junction boxW1747 Wiring Diagram Troubleshooting Moving parts have come to a complete stopCutting Headstock Assembly Parts Breakdown Headstock Assembly Parts List PART# DescriptionXPN09M Table, Base, and Columns Parts Breakdown Table, Base, and Columns Parts List Stand/Motor Assembly Parts Breakdown Stand/Motor Assembly Parts List Parts Warranty Warranty Registration CommentsBOX BELLINGHAM, WA
Top Page Image Contents