Woodstock W1747 To adjust the table parallelism, do these steps, Table micro-adjustment screws

Page 32

W1747 20" Planer

SERVICE

To adjust the table parallelism, do these steps:

1.DISCONNECT THE PLANER FROM THE POWER SOURCE!

2.Remove the motor access panel and locate the chain on the underside of the table.

3.Loosen the lock bolts and idler sprocket (see Chain Tension instructions on Page 28).

4.Mark the location of one tooth in the sprocket that you are adjusting.

5.Move the chain away from only the sprocket you want to adjust so only that sprocket can be turned independent of the chain.

Note: If the left side of the table is too high, the left two sprockets will need to be adjusted. Each tooth on the sprocket represents 0.016" of vertical movement as the cogs are turned. Make sure, as you turn the sprockets, to keep an accurate tooth count to ensure that the table is adjusted equally.

6.Carefully turn the sprocket (clockwise to raise the table; counterclockwise to lower the table) just enough to position the next tooth at the marked location, then fit the chain around sprocket again.

7.Repeat Steps 4–6with each sprocket that needs to be adjusted until the table-to-cutterhead clearance is within 0.016" from one side to the other.

8.Make sure the chain is properly fitted on the sprock- ets, and tighten the idler sprocket and lock bolts.

9.Micro-adjust the table position by loosening the cap screws (Figure 24) using a 6mm wrench, and lifting the table upward or downward until the table and cutterhead are in alignment.

Note: This process may require adjusting the col- umns on both the left and right hand sides until you find the correct combination.

10.Replace the motor access panel.

OFF

Figure 24. Table micro-adjustment screws.

-30-

Image 32

Contents Planer Page Contents Service Introduction Woodstock Technical SupportSpecifications Controls and Features Safety Standard Safety InstructionsAlways Lock Mobile Bases if Used Before Operating Machinery Additional Safety Instructions for Planers Electrical 220V OperationExtension Cords GroundingSET UP Items Needed for Set UpUnpacking InventoryHardware and Tools Machine PlacementLifting Planer Cleaning Machine These items are coated and must be cleanedExtension Wings Extension wing fasteners Leveling controlsDust Hood To install the handwheel, do these stepsHandwheel Connecting to Power Knife Setting GaugeGearbox Oil Level To check the gearbox oil level, do these stepsRecommended Adjustments Test RunTighten V-Belts To perform a test run, do these stepsOperations GeneralBasic Operation Basic steps of operating the planer are as followsOperation Tips Feed Speed Feed control knob positionsBed Rollers Adjustment Height Range 002-0.020To adjust the bed rollers, do these steps Accessories Planer AccessoriesOFF Maintenance Schedule MaintenanceCleaning To adjust/replace the V-belts, do these steps BeltsLubrication To inspect the knives, do these steps ServiceInspecting Knives Setting/Replacing Knives To set the knives, do these stepsTo adjust the chain tension, do these steps Chain TensionTable Parallelism Maximum Allowable TolerancesTo adjust the table parallelism, do these steps Table micro-adjustment screwsRollers, Chip Breaker Pressure Bar Heights Distance Below Knife Edge at *BDCRoller height adjustment 27, 28,Service To adjust roller spring tension, do these steps Spring TensionChip Deflector Gap Setting To adjust the deflector position, do these stepsScale Calibration To calibrate the scale, do these stepsAnti-Kickback Fingers Anti-kickback fingersPulley Alignment Checking belt alignmentW1747 Electrical Components W1747 motor junction boxW1747 Wiring Diagram Troubleshooting Moving parts have come to a complete stopCutting Headstock Assembly Parts Breakdown Headstock Assembly Parts List PART# DescriptionXPN09M Table, Base, and Columns Parts Breakdown Table, Base, and Columns Parts List Stand/Motor Assembly Parts Breakdown Stand/Motor Assembly Parts List Parts Warranty Warranty Registration CommentsBOX BELLINGHAM, WA