Woodstock W1683 instruction manual Assembly, Overview, Box Contents

Page 12

ASSEMBLY

The following is a description of the components shipped with the Shop Fox® W1683 20" Planer.

Should any parts be missing, examine the packaging carefully to be sure parts are not among the packing materials. If any key parts are missing, contact Woodstock International, Inc. at 360-734-3482 or by e-mail at: tech-support@woodstockint.com.

Overview

We have assembled most of your new planer for you at the factory; however, the parts shown in Figure 2 still need to be assembled after delivery. Please take your time and try to be as accurate as possible when following each step. This care will provide you with better results when you are finished.

Box Contents

1.Planer Unit

2.Dust Hood

3.Starter Switch

4.Rollers (2)

5.Handwheel

6.Hardware Bag:

(6)M6-1.0 x 12 Hex Bolts

(6)6mm Flat Washers

(8)1⁄2" Flat Washers

(8)M10-1.5 x 25 Hex Bolts

(1)Knife Setting Rod

(2)Knife Setting Gauge

(4)9mm E-Clip Ring

(1)Handle

(1)3mm Allen Wrench

(1)4mm Allen Wrench

(1)5mm Allen Wrench

(1)6mm Allen Wrench

(1)8mm & 10mm Combo Wrench

(1)12mm & 14mm Combo Wrench

(1)17mm & 19mm Combo Wrench

Additional Tools Required: Besides the tools that were included with the planer, you will also need a Phillips® screwdriver, a flat-head screwdriver and a good straightedge. A set of feeler gauges and a dial indicator will also be necessary for the Adjustments section.

Figure 2. Parts that need to be assembled.

Do not connect the machine to power at this time. The machine must

remain unplugged throughout the entire assembly process. Failure to do this may result in serious personal injury.

8

Image 12

Contents Planer Instruction Sheet Spiral Cutterhead PlanerW1718 Replacement Parts Page Table Of Contents Woodstock Service and Support Introduction About Your NEW PlanerWarranty and Returns Planer Machine SpecificationsSafety First Disconnect machine when cleaning, adjusting or servicingKeep proper footing and balance at all times Additional Safety Instructions for Planers Read the manualElectrical Requirements 220V OperationExtension Cords GroundingAssembly Box ContentsOverview Shop Preparation Cleaning Machine When assembling, adjusting or operating equipmentExtension Rollers Checking roller extension with a StraightedgeTo install the dust hood HandwheelDust Hood To mount the handwheelSwitch Knife Setting JigTo mount the switch To assemble the knife setting jigAdjustments Location of ControlsMoving Bed Rollers To move the bed rollersTo check the table Make sure machine is unplugged To adjust the table less than Checking table/head casting in frontTo adjust the table more than Remove the front cabinet coverChecking Knives To check the knivesKnife Adjustment 5 6 4 Feed Rollers, Chip Breaker & Pressure Bar Board position on tableChipbreaker adjustment controls Chip Deflector Anti-Kickback PawlsPlaner. To adjust the roller spring tension Chain TensionerSpring Tension To adjust the table roller height Table RollersAlways Wear Safety Glasses When Operating This machine OperationsTest Run Feed RateOperational Tips Face joint the concave side of cupped Stock before planingTroubleshooting Planing Results Aftermarket Setup Accessories Planer Pal knife setting jigMaintenance CleaningGeneral Table And BaseLubrication Worm gearBelt Tension Pulley AlignmentTo align the pulleys Wiring Diagram HP Magnetic Switch -L.Z. TypeTroubleshooting Symptom Possible Cause Corrective ActionClosure 107 100 103 108 101 104 102 8894 109 Headcasting 204 333 334 331 332 Page Middle Table 509 508 540 G8IKJ Warranty Card BOX BELLINGHAM, WA