Woodstock W1683 instruction manual Table Of Contents

Page 5

	Table Of Contents
		PAGE
1.	INTRODUCTION	2
	ABOUT YOUR NEW PLANER	2
	WOODSTOCK SERVICE AND SUPPORT	2
	WARRANTY AND RETURNS	3
	PLANER MACHINE SPECIFICATIONS	3
2.	SAFETY FIRST!	4
	SAFETY INSTRUCTIONS	4-5
	ADDITIONAL SAFETY INSTRUCTIONS FOR PLANERS	6
	ELECTRICAL REQUIREMENTS	7
	220V OPERATION	7
	EXTENSION CORDS	7
	GROUNDING	7
3.	ASSEMBLY	8
	BOX CONTENTS	8
	OVERVIEW	8
	SHOP PREPARATION	9
	CLEANING MACHINE	9
	EXTENSION ROLLERS	10
	HANDWHEEL	11
	DUST HOOD	11
	SWITCH	12
	KNIFE SETTING JIG	12
4.	ADJUSTMENTS	13
	LOCATION OF CONTROLS	13
	MOVING BED ROLLERS	14
	TABLE	14-16
	CHECKING KNIVES	17
	KNIFE ADJUSTMENT	18-19
	FEED ROLLERS, CHIPBREAKER & PRESSURE BAR	20-21
	CHIP DEFLECTOR	22
	ANTI-KICKBACK PAWLS	22
	CHAIN TENSIONER	23
	SPRING TENSION	23
	TABLE ROLLERS	24
5.	OPERATIONS	25
	TEST RUN	25
	FEED RATE	25
	OPERATIONAL TIPS	26
	TROUBLESHOOTING PLANING RESULTS	27
	AFTERMARKET SETUP ACCESSORIES	28
6.	MAINTENANCE	29
	GENERAL	29
	CLEANING	29
	TABLE AND BASE	29
	LUBRICATION	30
	BELT TENSION	31
	PULLEY ALIGNMENT	31
	WIRING DIAGRAM	32
	TROUBLESHOOTING	33
7.	CLOSURE	34
	DIAGRAMS AND PARTS LISTS	35-42
	WARRANTY AND REPLACEMENT	43

USE THE QUICK GUIDE PAGE LABELS TO SEARCH OUT INFORMATION FAST!

Image 5

Contents Planer Spiral Cutterhead Planer Instruction SheetW1718 Replacement Parts Page Table Of Contents Introduction About Your NEW Planer Woodstock Service and SupportPlaner Machine Specifications Warranty and ReturnsDisconnect machine when cleaning, adjusting or servicing Safety FirstKeep proper footing and balance at all times Read the manual Additional Safety Instructions for Planers220V Operation Electrical RequirementsExtension Cords GroundingOverview AssemblyBox Contents When assembling, adjusting or operating equipment Shop Preparation Cleaning MachineChecking roller extension with a Straightedge Extension RollersHandwheel To install the dust hoodDust Hood To mount the handwheelKnife Setting Jig SwitchTo mount the switch To assemble the knife setting jigLocation of Controls AdjustmentsTo check the table Make sure machine is unplugged Moving Bed RollersTo move the bed rollers Checking table/head casting in front To adjust the table less thanRemove the front cabinet cover To adjust the table more thanTo check the knives Checking KnivesKnife Adjustment 5 6 4 Board position on table Feed Rollers, Chip Breaker & Pressure BarChipbreaker adjustment controls Anti-Kickback Pawls Chip DeflectorSpring Tension Planer. To adjust the roller spring tensionChain Tensioner Table Rollers To adjust the table roller heightOperations Always Wear Safety Glasses When Operating This machineTest Run Feed RateFace joint the concave side of cupped Stock before planing Operational TipsTroubleshooting Planing Results Planer Pal knife setting jig Aftermarket Setup AccessoriesCleaning MaintenanceGeneral Table And BaseWorm gear LubricationTo align the pulleys Belt TensionPulley Alignment HP Magnetic Switch -L.Z. Type Wiring DiagramSymptom Possible Cause Corrective Action TroubleshootingClosure 107 100 103 108 101 104 102 8894 109 Headcasting 204 333 334 331 332 Page Middle Table 509 508 540 G8IKJ Warranty Card BOX BELLINGHAM, WA