Woodstock W1683 instruction manual Warranty and Returns, Planer Machine Specifications

Page 7

WARRANTY AND RETURNS

Woodstock International, Inc. warrants all SHOP FOX® machinery to be free of defects from workmanship and materials for a period of 2 years from the date of original purchase by the original owner. This warranty does not apply to defects due directly or indirectly to misuse, abuse, negligence or accidents, lack of maintenance, or to repair or alterations made or specifically authorized by anyone other than Woodstock International, Inc.

Woodstock International, Inc. will repair or replace, at its expense and at its option, the SHOP FOX® machine or machine part which in normal use has proven to be defective, provided that the original owner returns the product prepaid to the SHOP FOX® factory service center or authorized repair facility designated by our Bellingham, WA office, with proof of their purchase of the product within 2 years, and provides Woodstock International, Inc. reasonable opportunity to verify the alleged defect through inspection. If it is determined there is no defect, or that the defect resulted from causes not within the scope of Woodstock International Inc.'s warranty, then the original owner must bear the cost of storing and returning the product.

This is Woodstock International, Inc.'s sole written warranty and any and all warranties that may be implied by law, including any merchantability or fitness, for any particular purpose, are hereby limited to the duration of this written warranty. We do not warrant that SHOP FOX® machinery complies with the provisions of any law or acts. In no event shall Woodstock International, Inc.'s liability under this warranty exceed the purchase price paid for the product, and any legal actions brought against Woodstock International, Inc. shall be tried in the State of Washington, County of Whatcom. We shall in no event be liable for death, injuries to persons or property or for incidental, contingent, special or consequential damages arising from the use of our products.

Every effort has been made to ensure that all SHOP FOX® machinery meets high quality and durability standards. We reserve the right to change specifications at any time because of our commitment to continuously improve the quality of our products.

Planer Machine Specifications

Motor

5 H.P., 220V, Single-Phase

Amps

28

Cutting Width

20"

Cutting Height

8"

Minimum Stock Thickness

14"

Minimum Stock Length

7"

Maximum Depth of Cut

18"

Cutterhead Diameter

3316"

Cutterhead Speed

5500 R.P.M.

Table Size

2534" x 20"

Knives

4 H.S.S.

Feed Rates

18 & 23 F.P.M.

3

Image 7
Contents Planer Spiral Cutterhead Planer Instruction SheetW1718 Replacement Parts Page Table Of Contents Introduction About Your NEW Planer Woodstock Service and SupportPlaner Machine Specifications Warranty and ReturnsDisconnect machine when cleaning, adjusting or servicing Safety FirstKeep proper footing and balance at all times Read the manual Additional Safety Instructions for PlanersGrounding Electrical Requirements220V Operation Extension CordsBox Contents AssemblyOverview When assembling, adjusting or operating equipment Shop Preparation Cleaning MachineChecking roller extension with a Straightedge Extension RollersTo mount the handwheel To install the dust hoodHandwheel Dust HoodTo assemble the knife setting jig SwitchKnife Setting Jig To mount the switchLocation of Controls AdjustmentsTo move the bed rollers Moving Bed RollersTo check the table Make sure machine is unplugged Checking table/head casting in front To adjust the table less thanRemove the front cabinet cover To adjust the table more thanTo check the knives Checking KnivesKnife Adjustment 5 6 4 Board position on table Feed Rollers, Chip Breaker & Pressure BarChipbreaker adjustment controls Anti-Kickback Pawls Chip DeflectorChain Tensioner Planer. To adjust the roller spring tensionSpring Tension Table Rollers To adjust the table roller heightFeed Rate Always Wear Safety Glasses When Operating This machineOperations Test RunFace joint the concave side of cupped Stock before planing Operational TipsTroubleshooting Planing Results Planer Pal knife setting jig Aftermarket Setup AccessoriesTable And Base MaintenanceCleaning GeneralWorm gear LubricationPulley Alignment Belt TensionTo align the pulleys HP Magnetic Switch -L.Z. Type Wiring DiagramSymptom Possible Cause Corrective Action TroubleshootingClosure 107 100 103 108 101 104 102 8894 109 Headcasting 204 333 334 331 332 Page Middle Table 509 508 540 G8IKJ Warranty Card BOX BELLINGHAM, WA