Woodstock W1683 instruction manual Checking Knives, To check the knives

Page 21

Figure 15. Cover removed from planer.

These Points Must

All Touch Evenly

Figure 16. Correct jig position on cutterhead.

Checking Knives

The Model W1683 features a 4 knife cutterhead. These knives must be checked and adjusted after regular use. Adjusting the knives is also an important part of the maintenance process. Correctly positioned knives act as a reference point for adjusting the feed rollers, the chip breaker and the pressure bar.

When checking/adjusting the knives, keep in mind that the knife edge should be as precise as possible at tolerances within .002" from one end to the other. Improperly adjusted knives may unbalance the cutterhead, reduce the sharpness of knife edges prematurely, shorten bearing life, and produce poor planing results.

To check the knives:

1.Remove the upper cover as shown in Figure 15 so you have access to the top of the cutterhead.

2.Remove the V-belt cover from the left-hand side of the planer (facing front).

3.Using the V-belt to rotate the cutterhead, turn the cutterhead so one of the knives is accessible.

4.Place the knife setting jig on the cutterhead. Both feet should sit solidly on the cutterhead and the knife should barely touch the center of the jig as shown in Figure 16.

5.If the knife does not contact the center of the jig, or if the knife contacts the center of the jig but both feet will not sit solidly on the cutterhead, then the knives will need to be adjusted.

For quick and easy knife setup, consider purchasing a Planer Pal®. This handy tool allows you to quickly set the knives to within .001" from one end to the other. See “Aftermarket Accessories” at the end of the Operations section for more details.

17

Page 20 Page 22
Image 21
Page 20 Page 22
Contents Planer Spiral Cutterhead Planer Instruction SheetW1718 Replacement Parts Page Table Of Contents Introduction About Your NEW Planer Woodstock Service and SupportPlaner Machine Specifications Warranty and ReturnsDisconnect machine when cleaning, adjusting or servicing Safety FirstKeep proper footing and balance at all times Read the manual Additional Safety Instructions for Planers220V Operation Electrical RequirementsExtension Cords GroundingAssembly Box ContentsOverview When assembling, adjusting or operating equipment Shop Preparation Cleaning MachineChecking roller extension with a Straightedge Extension RollersHandwheel To install the dust hoodDust Hood To mount the handwheelKnife Setting Jig SwitchTo mount the switch To assemble the knife setting jigLocation of Controls AdjustmentsMoving Bed Rollers To move the bed rollersTo check the table Make sure machine is unplugged Checking table/head casting in front To adjust the table less thanRemove the front cabinet cover To adjust the table more thanTo check the knives Checking KnivesKnife Adjustment 5 6 4 Board position on table Feed Rollers, Chip Breaker & Pressure BarChipbreaker adjustment controls Anti-Kickback Pawls Chip DeflectorPlaner. To adjust the roller spring tension Chain TensionerSpring Tension Table Rollers To adjust the table roller heightOperations Always Wear Safety Glasses When Operating This machineTest Run Feed RateFace joint the concave side of cupped Stock before planing Operational TipsTroubleshooting Planing Results Planer Pal knife setting jig Aftermarket Setup AccessoriesCleaning MaintenanceGeneral Table And BaseWorm gear LubricationBelt Tension Pulley AlignmentTo align the pulleys HP Magnetic Switch -L.Z. Type Wiring DiagramSymptom Possible Cause Corrective Action TroubleshootingClosure 107 100 103 108 101 104 102 8894 109 Headcasting 204 333 334 331 332 Page Middle Table 509 508 540 G8IKJ Warranty Card BOX BELLINGHAM, WA
Top Page Image Contents