Woodstock W1683 Safety First, Disconnect machine when cleaning, adjusting or servicing

Page 8

SAFETY FIRST!

READ MANUAL BEFORE OPERATING MACHINE

FAILURE TO FOLLOW INSTRUCTIONS BELOW WILL

RESULT IN PERSONAL INJURY

Indicates an imminently hazardous situation which, if not avoided, WILL result in death or serious injury.

Indicates a potentially hazardous situation which, if not avoided, COULD result in death or serious injury.

Indicates a potentially hazardous situation which, if not avoided, MAY result in minor or moderate injury. It may also be used to alert against unsafe practices.

This symbol is used to alert the user to useful information about proper NOTICE operation of the equipment.

1.Thoroughly read the instruction manual before operating your machine. Learn the applications, limitations and potential hazards of this machine. Keep manual in a safe, convenient place for future reference.

2.Keep work area clean and well lighted. Clutter and inadequate lighting invite potential hazards.

3.Ground all tools. If a machine is equipped with a three-prong plug, it must be plugged into a three- hole electrical outlet or grounded extension cord. If using an adapter to aid in accommodating a two- hole receptacle, ground using a screw to a known ground.

4.Wear eye protection at all times. Use safety glasses with side shields or safety goggles (that meet the national safety standards) while operating this machine.

5.Avoid dangerous environments. Do not operate this machine in wet or open flame environments. Airborne dust particles could cause an explosion and severe fire hazard.

6.Ensure all guards are securely in place and in working condition.

7.Make sure switch is in the “OFF” position before connecting power to machine.

8.Keep work area clean and free of clutter, grease, etc.

9.Keep children and visitors away. All visitors should be kept a safe distance away while operating unit.

10.Childproof workshop with padlocks, master switches or by removing switch keys.

11.Disconnect machine when cleaning, adjusting or servicing.

12.Do not force tool. The machine will do a safer and better job at the rate for which it was designed.

4

Page 7 Page 9
Image 8
Page 7 Page 9
Contents Planer Instruction Sheet Spiral Cutterhead PlanerW1718 Replacement Parts Page Table Of Contents Woodstock Service and Support Introduction About Your NEW PlanerWarranty and Returns Planer Machine SpecificationsSafety First Disconnect machine when cleaning, adjusting or servicingKeep proper footing and balance at all times Additional Safety Instructions for Planers Read the manualElectrical Requirements 220V OperationExtension Cords GroundingOverview AssemblyBox Contents Shop Preparation Cleaning Machine When assembling, adjusting or operating equipmentExtension Rollers Checking roller extension with a StraightedgeTo install the dust hood HandwheelDust Hood To mount the handwheelSwitch Knife Setting JigTo mount the switch To assemble the knife setting jigAdjustments Location of ControlsTo check the table Make sure machine is unplugged Moving Bed RollersTo move the bed rollers To adjust the table less than Checking table/head casting in frontTo adjust the table more than Remove the front cabinet coverChecking Knives To check the knivesKnife Adjustment 5 6 4 Feed Rollers, Chip Breaker & Pressure Bar Board position on tableChipbreaker adjustment controls Chip Deflector Anti-Kickback PawlsSpring Tension Planer. To adjust the roller spring tensionChain Tensioner To adjust the table roller height Table RollersAlways Wear Safety Glasses When Operating This machine OperationsTest Run Feed RateOperational Tips Face joint the concave side of cupped Stock before planingTroubleshooting Planing Results Aftermarket Setup Accessories Planer Pal knife setting jigMaintenance CleaningGeneral Table And BaseLubrication Worm gearTo align the pulleys Belt TensionPulley Alignment Wiring Diagram HP Magnetic Switch -L.Z. TypeTroubleshooting Symptom Possible Cause Corrective ActionClosure 107 100 103 108 101 104 102 8894 109 Headcasting 204 333 334 331 332 Page Middle Table 509 508 540 G8IKJ Warranty Card BOX BELLINGHAM, WA
Top Page Image Contents