Woodstock W1683 instruction manual Keep proper footing and balance at all times

Page 9

13.Use correct tool. Do not force machine or attachment to do a job for which it was not designed.

14.Wear proper apparel. Do not wear loose clothing, neck ties, gloves, jewelry, etc.

15.Remove adjusting keys and wrenches before turning the machine on. Make this a habit!

16.Use proper extension cord. When using an extension cord, make sure it is in good condition. Use extension cords 100' or less in length that are rated Hard Service (grade S) or better, and that have a conductor size of 16 A.W.G. A drop in line voltage, loss of power and overheating can result when using an undersized cord. The extension cord must have a ground wire and ground plug pin, as well.

17.Keep proper footing and balance at all times.

18.Do not leave machine unattended—wait until it comes to a complete stop before leaving the area.

19.Perform machine maintenance and care. Follow lubrication and accessory attachment instructions in the manual.

20.Keep machine away from open flame. Operating machines near pilot lights and/or open flames creates a high risk if dust is dispersed in the area. Dust particles and an ignition source may cause an explosion. Do not operate the machine in high risk areas, including but not limited to, those mentioned above.

21.Do not use machine under the influence of drugs or alcohol or if you are excessively tired.

22.Do not let untrained people use the machine if they are not supervised by an experienced operator.

23.If at any time you are experiencing difficulties performing the intended operation, stop using the machine! Then contact our service department or ask a qualified expert how the operation should be performed.

24.Mag switches can be accidentally turned on when they are bumped. Always be aware of the mag switch location when moving items around the shop.

Operating this equipment has the potential for flying debris to cause eye injury. Always wear safety glasses or goggles when operating equipment. Everyday glasses or reading glasses only have impact resistant lenses, they are not safety glasses. Be certain the safety glasses you wear meet the appropriate standards of the American National Standards Institute (ANSI).

5

Page 8 Page 10
Image 9
Page 8 Page 10
Contents Planer Spiral Cutterhead Planer Instruction SheetW1718 Replacement Parts Page Table Of Contents Introduction About Your NEW Planer Woodstock Service and SupportPlaner Machine Specifications Warranty and ReturnsDisconnect machine when cleaning, adjusting or servicing Safety FirstKeep proper footing and balance at all times Read the manual Additional Safety Instructions for Planers220V Operation Electrical RequirementsExtension Cords GroundingAssembly Box ContentsOverview When assembling, adjusting or operating equipment Shop Preparation Cleaning MachineChecking roller extension with a Straightedge Extension RollersHandwheel To install the dust hoodDust Hood To mount the handwheelKnife Setting Jig SwitchTo mount the switch To assemble the knife setting jigLocation of Controls AdjustmentsMoving Bed Rollers To move the bed rollersTo check the table Make sure machine is unplugged Checking table/head casting in front To adjust the table less thanRemove the front cabinet cover To adjust the table more thanTo check the knives Checking KnivesKnife Adjustment 5 6 4 Board position on table Feed Rollers, Chip Breaker & Pressure BarChipbreaker adjustment controls Anti-Kickback Pawls Chip DeflectorPlaner. To adjust the roller spring tension Chain TensionerSpring Tension Table Rollers To adjust the table roller heightOperations Always Wear Safety Glasses When Operating This machineTest Run Feed RateFace joint the concave side of cupped Stock before planing Operational TipsTroubleshooting Planing Results Planer Pal knife setting jig Aftermarket Setup AccessoriesCleaning MaintenanceGeneral Table And BaseWorm gear LubricationBelt Tension Pulley AlignmentTo align the pulleys HP Magnetic Switch -L.Z. Type Wiring DiagramSymptom Possible Cause Corrective Action TroubleshootingClosure 107 100 103 108 101 104 102 8894 109 Headcasting 204 333 334 331 332 Page Middle Table 509 508 540 G8IKJ Warranty Card BOX BELLINGHAM, WA
Top Page Image Contents