Omron ZS-MDC user manual Open the connector cover on the con- troller, Removal procedure

Page 30

Section 2 INSTALLATION

Section 2

Multi-Controller

3. Open the connector cover on the con- troller.

Slide the cover to remove.

4. Insert the Controller Link Unit into the connector on the Multi-Controller.

The connectors are designed to be connected in a particular direction. Insert the connector in the direc- tion so that the indented section of the Controller Link Unit in the figure on the right matches the con- nector protrusion on the Data Storage Unit.

			Controller
L	LD O	ENABLE				Link Unit (sold
H	LD O
	N Z
P	ERO
						separately)
		H	LD	ON
		P			ZERO	ENABLE
		L				ENABLE

Indented section

& CONNECTION

5. Slide the Sensor Controller to insert to the Controller Link Unit connector.

●Removal procedure

The following describes how to remove the Multi-Controller and Sensor Controller from the DIN track.

1. Slide and remove the Sensor Controller from the connector on the Controller Link Unit.

2. Slide the Controller Link Unit and

remove from the connector on the Multi-

Controller.

H	LD
P
L

ON	ZERO
	ZERO	ENABLE
		ENABLE

		Controller
		Link Unit
				(sold sepa-
				rately)
H	LDON	ZERO
P		ZERO	ENA
L			ENA	BLE

3. Install the cover on the coupler of the controller.

2-6

ZS-MDC

User’s Manual

Image 30

Contents Smart Sensor How to Switch the Display Language to English IntroductionEction Smart Sensors Multi-Controller ZS-MDCRead and Understand this Document Suitability for USE Dimensions and Weights Installation Environment Power Supply and WiringOthers Precautions for Correct Use Installation SiteOrientation when Installing the Multi-Controller Maintenance and InspectionWarming Up Editors Note FormatMeaning of Symbols Visual AidsMemo Contents Introduction Contents Features Wide Range of Logic Operation Functions Multi-Controller FeaturesSupports Connection to Up to 9 Sensor Controllers Completely Digitally Based Logic Operation ProcessingSame Compact Size as Sensor Controller USB ConnectionDedicated Software SmartMonitor Zero Measurement of Stepped Workpieces Multi-Controller ApplicationsMeasurement of Workpiece Thickness at Multiple Locations Measurement of Average Workpiece HeightMeasurement of Workpiece Flatness Measurement of Workpiece StrainBatch-acquisition of Multi-point Measurement Data Gang-mounted Sensor Controllers can be set up State of gang-mounted Sensor Controllers can be monitoredBasic Configuration ZS-MDC11/MDC41Part Names and Functions LOW indicator Mode SwitchThreshold Selector Switch Pass indicatorMemo Installation & Connection Installation & ConnectionChecking the installation site About Installation and ConnectionChecking the installation environment About the power supply Multi-Controller Attaching the ferrite coreInstalling the Multi-Controller About channel No. when controllers are gang-mountedCH0 CH1 CH2 CH3 CH9 Installing on the DIN track Installation procedurePFP-M Open the connector cover on the con- troller Removal procedureInstall the cover on the coupler of the controller Installation & Connection Installation Mounting on a panelAttached onto the panel from the front Install the Multi-Controller and SensorController with Panel Mount Adapters Hook the hooks of the mounting fixtureWiring the I/O cable About the I/O cableLinear output OUT3 Enable outputOUT4 Busy output Linear GNDCircuit Diagrams NPN type ZS-MDC11 Installation & ConnectionPNP type ZS-MDC41 Memo Setup Setting Flow Installation and ConnectionWhen a Problem Occurs About Setup Switching ModesBasic Knowledge for Operation FUN Mode Displays and Key OperationsPress function key 2 representing on Press the Menu key to return to the top menuVoltage Current RUN ModeThresh ResoluTeach Mode Teaching DirectList of Setting Items FUN ModeWhen TASK1 is selected COM Mode TimerAdjust SET NO-MEASWhen other than TASK1 is selected Bank SystemRUN Mode Teach ModeSelecting Tasks Setting Assignments Setting Logic Operation Methods Setting I/O Assignments Switching banks by external signal inputAbout Digital Output Changing Output AssignmentsChanging Linear Output Assignments TASK3 TASK4Memo Application Setting Examples Application Setting ExamplesApplication Setting ExamplesSelect TASK1 Set the expression of TASK1SENSING-CALC-CALC-MAX-MIN Measuring the Relative Difference between Steps ApplicationFollowing the same procedure as 2 to 3, set Up TASK3 Set the expression of TASK1To linear-output the operation result I/O SET-I/O SET-ANALOG Measuring the Reference Difference between Steps Following the same procedure as 2 to 3, set Up TASK2 Select TASK1 or TASK2 depending onDetails to be output Measuring Flatness CH0 CH1 CH2 CH3 CH9TASK12 TASK2 TASK34 TASK4 Input a Input B Input C Measuring the Average Height Average to ON, and other inputs to OFF Select TASK1 so that the average value can be linear-outputMeasuring the Twist of a Workpiece CH0 CH1 CH2 CH3 CH4Input X Input D Input Y Input C Select TASK3 so that the judgment on the twist can be output Select TASK3 so that the twist value can be linear-outputMeasuring the Warp of a Workpiece CH0 CH1 CH2 CH3Select TASK1 Application Setting Examples Select TASK2 so that the judgment on the warp can be output Select TASK2 so that the warp value can be linear-outputMemo Appendix Troubleshooting When all digits on the main display and sub-display blink Error Messages and CountermeasuresWhen Error Is Displayed on the Main Display OthersOr more of the rated measuring range Glossary Specifications and External Dimensions Multi-ControllerZS-MDC11 ZS-MDC41 PASS/LOWShock resistance destructive Panel Mount Adapters ZS-XPM1/XPM2RS-232C Cable for Connecting to a Personal Computer ZS-XRS2Controller Link Unit ZS-XCNVersion Up Information Ver1.00 to Ver1.50Ver1.50 to Ver2.00 Index Section IndexUSB Memo Revision History Z209-E1-01Terms and Conditions of Sale Omron Electronics LLC