Omron ZS-MDC user manual Measuring the Twist of a Workpiece, CH0 CH1 CH2 CH3 CH4

Page 70

Section 4 APPLICATION SETTING EXAMPLES

Section 4

Measuring the Twist of a Workpiece

Measuring the Twist of a Workpiece

This is an example of how to measure the height at 4 locations on a workpiece, and calculate the difference (twist) between each of the measured values. Use [X-Y] for the expression.

Input A

Input D

Input B

Input C

Input A Input B Input C Input D

CH0 CH1 CH2 CH3 CH4

The operation and/or measurement results are output as judgement output or linear output.

For details on how to connect and install the Sensor Heads and Sensor Controllers, refer to the “ZS-L User’s Manual”.

▲FUN Mode-[SENSING]-[SEL CH]

1. Assign the CH No. of the controller to inputs A to C to be used for the expression.

INPUT A:1CH

INPUT B:2CH

INPUT C:3CH

	1	INPUT A	2	INPUT B

	3	INPUT C

4-14

ZS-MDC

User’s Manual

Image 70

Contents Smart Sensor How to Switch the Display Language to English IntroductionEction Smart Sensors Multi-Controller ZS-MDCRead and Understand this Document Suitability for USE Dimensions and Weights Power Supply and Wiring Installation EnvironmentOthers Precautions for Correct Use Installation SiteMaintenance and Inspection Orientation when Installing the Multi-ControllerWarming Up Editors Note FormatMeaning of Symbols Visual AidsMemo Contents Introduction Contents Features Wide Range of Logic Operation Functions Multi-Controller FeaturesSupports Connection to Up to 9 Sensor Controllers Completely Digitally Based Logic Operation ProcessingUSB Connection Same Compact Size as Sensor ControllerDedicated Software SmartMonitor Zero Measurement of Stepped Workpieces Multi-Controller ApplicationsMeasurement of Workpiece Thickness at Multiple Locations Measurement of Average Workpiece HeightMeasurement of Workpiece Strain Measurement of Workpiece FlatnessBatch-acquisition of Multi-point Measurement Data Gang-mounted Sensor Controllers can be set up State of gang-mounted Sensor Controllers can be monitoredBasic Configuration ZS-MDC11/MDC41Part Names and Functions LOW indicator Mode SwitchThreshold Selector Switch Pass indicatorMemo Installation & Connection Installation & ConnectionChecking the installation site About Installation and ConnectionChecking the installation environment About the power supplyMulti-Controller Attaching the ferrite coreAbout channel No. when controllers are gang-mounted Installing the Multi-ControllerCH0 CH1 CH2 CH3 CH9 Installation procedure Installing on the DIN trackPFP-M Removal procedure Open the connector cover on the con- trollerInstall the cover on the coupler of the controller Installation & Connection Installation Mounting on a panelAttached onto the panel from the front Install the Multi-Controller and SensorController with Panel Mount Adapters Hook the hooks of the mounting fixtureWiring the I/O cable About the I/O cableLinear output OUT3 Enable outputOUT4 Busy output Linear GNDCircuit Diagrams NPN type ZS-MDC11 Installation & ConnectionPNP type ZS-MDC41 Memo Setup Setting Flow Installation and ConnectionWhen a Problem Occurs Switching Modes About SetupBasic Knowledge for Operation FUN Mode Displays and Key OperationsPress function key 2 representing on Press the Menu key to return to the top menuVoltage Current RUN ModeThresh ResoluTeach Mode Teaching DirectFUN Mode List of Setting ItemsWhen TASK1 is selected COM Mode TimerAdjust SET NO-MEASWhen other than TASK1 is selected Bank SystemRUN Mode Teach ModeSelecting Tasks Setting Assignments Setting Logic Operation Methods Setting I/O Assignments Switching banks by external signal inputAbout Digital Output Changing Output AssignmentsChanging Linear Output Assignments TASK3 TASK4Memo Application Setting Examples Application Setting ExamplesApplication Setting ExamplesSelect TASK1 Set the expression of TASK1SENSING-CALC-CALC-MAX-MIN Measuring the Relative Difference between Steps ApplicationFollowing the same procedure as 2 to 3, set Up TASK3 Set the expression of TASK1To linear-output the operation result I/O SET-I/O SET-ANALOG Measuring the Reference Difference between Steps Select TASK1 or TASK2 depending on Following the same procedure as 2 to 3, set Up TASK2Details to be output Measuring Flatness CH0 CH1 CH2 CH3 CH9 TASK12 TASK2 TASK34 TASK4 Input a Input B Input C Measuring the Average Height Average to ON, and other inputs to OFF Select TASK1 so that the average value can be linear-outputMeasuring the Twist of a Workpiece CH0 CH1 CH2 CH3 CH4Input X Input D Input Y Input C Select TASK3 so that the judgment on the twist can be output Select TASK3 so that the twist value can be linear-outputMeasuring the Warp of a Workpiece CH0 CH1 CH2 CH3Select TASK1 Application Setting Examples Select TASK2 so that the judgment on the warp can be output Select TASK2 so that the warp value can be linear-outputMemo Appendix Troubleshooting When all digits on the main display and sub-display blink Error Messages and CountermeasuresWhen Error Is Displayed on the Main Display OthersOr more of the rated measuring range Glossary Specifications and External Dimensions Multi-ControllerZS-MDC11 ZS-MDC41 PASS/LOWShock resistance destructive Panel Mount Adapters ZS-XPM1/XPM2RS-232C Cable for Connecting to a Personal Computer ZS-XRS2Controller Link Unit ZS-XCNVer1.00 to Ver1.50 Version Up InformationVer1.50 to Ver2.00 Index Section IndexUSB Memo Revision History Z209-E1-01Terms and Conditions of Sale Omron Electronics LLC