Omron ZS-MDC user manual When a Problem Occurs

Page 41

Section 3

Setting Flow

When a Problem Occurs...

The Multi-Controller does not operate correctly.

Troubleshooting p.5-2

Want to know the meanings of terms

An error message has appeared

When [Error] is Displayed on the Main Display p.5-3

Section

Glossary p.5-5

	FunctionsofUse
	FunctionsofUse	Setting Banks
		Setting Banks
		Set up the banks.	Sensor Controller User's Manual,
			Section 3 Setup


	Applied	Set Up the System Environment
	Applied	Set up the system environment.	Sensor Controller User's Manual,
			Sensor Controller User's Manual,
			Section 3 Setup
			Section 3 Setup
	Functions

		Setting the Display Method
		Setting the Display Method
		Set what is to be displayed on the Multi-	Sensor Controller User's Manual,
	Additional	Controller during measurement in the RUN	Section 3 Setup
	Additional	mode.
		mode.

3 SETUP

ZS-MDC

User’s Manual

3-3

Image 41

Contents Smart Sensor Introduction How to Switch the Display Language to EnglishSmart Sensors Multi-Controller ZS-MDC EctionRead and Understand this Document Suitability for USE Dimensions and Weights Others Installation EnvironmentPower Supply and Wiring Installation Site Precautions for Correct UseWarming Up Orientation when Installing the Multi-ControllerMaintenance and Inspection Format Editors NoteVisual Aids Meaning of SymbolsMemo Contents Introduction Contents Features Supports Connection to Up to 9 Sensor Controllers Multi-Controller FeaturesWide Range of Logic Operation Functions Completely Digitally Based Logic Operation ProcessingDedicated Software SmartMonitor Zero Same Compact Size as Sensor ControllerUSB Connection Measurement of Workpiece Thickness at Multiple Locations Multi-Controller ApplicationsMeasurement of Stepped Workpieces Measurement of Average Workpiece HeightBatch-acquisition of Multi-point Measurement Data Measurement of Workpiece FlatnessMeasurement of Workpiece Strain State of gang-mounted Sensor Controllers can be monitored Gang-mounted Sensor Controllers can be set upZS-MDC11/MDC41 Basic ConfigurationPart Names and Functions Threshold Selector Switch Mode SwitchLOW indicator Pass indicatorMemo Installation & Connection Installation & ConnectionChecking the installation environment About Installation and ConnectionChecking the installation site About the power supplyAttaching the ferrite core Multi-ControllerCH0 CH1 CH2 CH3 CH9 Installing the Multi-ControllerAbout channel No. when controllers are gang-mounted PFP-M Installing on the DIN trackInstallation procedure Install the cover on the coupler of the controller Open the connector cover on the con- trollerRemoval procedure Installation & Connection Mounting on a panel InstallationController with Panel Mount Adapters Install the Multi-Controller and SensorAttached onto the panel from the front Hook the hooks of the mounting fixtureAbout the I/O cable Wiring the I/O cableOUT4 Busy output OUT3 Enable outputLinear output Linear GNDNPN type ZS-MDC11 Installation & Connection Circuit DiagramsPNP type ZS-MDC41 Memo Setup Installation and Connection Setting FlowWhen a Problem Occurs Basic Knowledge for Operation About SetupSwitching Modes Displays and Key Operations FUN ModePress the Menu key to return to the top menu Press function key 2 representing onThresh RUN ModeVoltage Current ResoluTeaching Direct Teach ModeWhen TASK1 is selected List of Setting ItemsFUN Mode Adjust TimerCOM Mode SET NO-MEASBank System When other than TASK1 is selectedTeach Mode RUN ModeSelecting Tasks Setting Assignments Setting Logic Operation Methods Switching banks by external signal input Setting I/O AssignmentsChanging Linear Output Assignments Changing Output AssignmentsAbout Digital Output TASK3 TASK4Memo Application Setting Examples Application Setting ExamplesExamples Application SettingSet the expression of TASK1 Select TASK1SENSING-CALC-CALC-MAX-MIN Application Measuring the Relative Difference between StepsSet the expression of TASK1 Following the same procedure as 2 to 3, set Up TASK3To linear-output the operation result I/O SET-I/O SET-ANALOG Measuring the Reference Difference between Steps Details to be output Following the same procedure as 2 to 3, set Up TASK2Select TASK1 or TASK2 depending on CH0 CH1 CH2 CH3 CH9 Measuring FlatnessTASK12 TASK2 TASK34 TASK4 Input a Input B Input C Measuring the Average Height Select TASK1 so that the average value can be linear-output Average to ON, and other inputs to OFFCH0 CH1 CH2 CH3 CH4 Measuring the Twist of a WorkpieceInput X Input D Input Y Input C Select TASK3 so that the twist value can be linear-output Select TASK3 so that the judgment on the twist can be outputCH0 CH1 CH2 CH3 Measuring the Warp of a WorkpieceSelect TASK1 Application Setting Examples Select TASK2 so that the warp value can be linear-output Select TASK2 so that the judgment on the warp can be outputMemo Appendix Troubleshooting When Error Is Displayed on the Main Display Error Messages and CountermeasuresWhen all digits on the main display and sub-display blink OthersOr more of the rated measuring range Glossary Multi-Controller Specifications and External DimensionsPASS/LOW ZS-MDC11 ZS-MDC41Shock resistance destructive ZS-XPM1/XPM2 Panel Mount AdaptersZS-XRS2 RS-232C Cable for Connecting to a Personal ComputerZS-XCN Controller Link UnitVer1.50 to Ver2.00 Version Up InformationVer1.00 to Ver1.50 Section Index IndexUSB Memo Z209-E1-01 Revision HistoryTerms and Conditions of Sale Omron Electronics LLC