Lincoln Electric IM10018-A manual Stacking Hole Stacking Pins, Safety Precautions

Page 10

A-2

INSTALLATION

A-2

 

 

 

SAFETY PRECAUTIONS

Read entire Installation Section before installing the IDEALARC® DC-600 VRD.

ELECTRIC SHOCK CAN KILL.

WARNING

• Only qualified personnel should install this machine.

•Turn the input power OFF at the disconnect switch or fuse box before working on the equipment.

•Do not touch electrically hot parts.

•Always connect the IDEALARC® DC-600 VRD grounding terminal to a good electrical earth ground.

•Set the IDEALARC® DC-600 VRD Power ON/OFF PUSH bUTTON to the OFF position when con- necting power cord to input power.

__________________

SELECT PROPER LOCATION

Place the welder where clean cooling air can freely circulate in through the front louvers and out through the rear louvers. Dirt, dust or any foreign material that can be drawn into the welder should be kept at a mini- mum. Failure to observe these precautions can result in excessive operating temperatures and nuisance shut-downs.

LIMIT ON STACKING

WARNING

•Lift only with equipment of ade- quate lifting capacity.

•be sure machine is stable when lifting.

•Do not lift this machine using lift bail if it is equipped with a heavy

 

accessory such as trailer or gas

 

cylinder.

FALLING

• Do not lift machine if lift bail is

EQUIPMENT can

damaged.

cause injury.

• Do not operate machine while

 

suspended from lift bail.

•Do not stack more than three high.

•Do not stack the IDEALARC® DC-600 VRD on top of any other machine.

------------------------------------------------------------------------

STACKING

Three IDEALARC® DC-600 VRD machines can be stacked.

DO NOT stack more than three machines in one grouping.

DO NOT stack the IDEALARC® DC-600 VRD on another type of machine.

Follow these guidelines when stacking:

1.Select a firm, level surface capable of supporting the total weight of up to three machines (1570 pounds/712 kilograms).

2.Set the bottom machine in place.

3.Stack the second machine on top of it by aligning the two holes in the base rails of the second machine with the two pins on top front of the bot- tom machine.

4.Repeat process for third machine.

NOTE: The machines must be stacked with the Case Front of each machine flush with each other. See Figure A.1.

FIGURE A.1 - Stacking IDEALARC® DC-600 VRD machines

STACKING HOLE

STACKING PINS

TILTING

The IDEALARC® DC-600 VRD must be placed on a stable, level surface so it will not topple over.

IDEALARC® DC-600 VRD

Page 9 Page 11
Image 10
Page 9 Page 11
Contents Safety Depends on You Idealarc DC-600 VRDSafety California Proposition 65 WarningsElectric Shock can kill Welding and Cutting Sparks can Cause fire or explosion IiiSafety Please Examine Carton and Equipment For Damage Immediately On-Line Product Registration TAbLE of Contents TAbLE of Contents Installation Technical Specifications Idealarc DC-600 VRDElectric Shock can Kill Stacking Hole Stacking PinsSafety Precautions Select Proper LocationElectrical Input Connections Fuse and Wire SIzESInput Power Supply Connections Ground ConnectionReconnect Procedure See Machine Rating Plate for Required Input Supply VoltageOutput Connections ELECTRODE, Work and #21 Lead ConnectionsTerminal Strip 1 T.S.1 Auxiliary Power and Control CONNections Terminal Strip 2 T.S.2Fumes and Gases can be dangerous Electric Shock can killARC Rays can burn General Description Design Features and AdvantagesOperation Recommended Processes and EQUIP- MentOutput Control Output Voltage Current OFF Input PowerOutput Terminals Power Light Controls and SettingsInput Power ON/OFF Switch NectionAuxiliary Power in MS-RECEP- Tacle OVERLOAD, OVERCURRENT, and Fault Protection For codes 11707 and aboveCV Mode Remote Control of Machine OperationWelding Procedure Recommendations CC ModeNA-3 Automatic Wire Feeder Operation Field Installed Options AccessoriesWire Feeders and Tractors Factory or Field Installed OptionsFigure C.2 MULTI-PROCESS Switch CAbLE Connections Accessories Safety Precautions Electric Shock can Kill 1MAINTENANCED-1Routine and Periodic Maintenance TROUbLESHOOTING Devices Board can be damaged by static electricityStatic-Sensitive Handle only atOutput PRObLEMS TROUbLESHOOTING LOCAL/REMOTE Switch TROUbLESHOOTING Check all Three-Phase input Facility PRObLEMS Symptoms Welding PRObLEMS Poor arc characteristics in all processes BOARD TROUbLESHOOTING Guide Control P.C. bOARDBOARD TROUbLESHOOTING Guide VRD P.C. bOARD Checking Power ON/OFF Switch S1Connecting Remote Output Control Rheostat to the Machine Checking Output Control RHEO- Stat on Machine R1Diagrams Diagrams Diagrams Diagrams Connection of LN-742 to the DC-600 VRD Power Source FeederConnection of LN-7 to the DC-600 VRD Power Source Connection of LN-8 or LN-9 to the DC-600 VRD Power Source 600Control Cable Connection of NA-5/-5R to the DC-600 VRD Power Source Lincoln Wire DC-600 VRD Dimension Print with K817P Undercarriage DC-600 VRD Dimension Print with K842 Undercarriage Precaucion Warnung
Top Page Image Contents