Black & Decker 90528116, BDTS200 instruction manual Assembling Stand, SAW to Stand

Page 11

ASSEMBLING STAND

1.Attach the rubber feet (H) Fig. 11 to the bottom of each leg (F).

Locate the two legs (F) which have holes at the bottom for attaching the wheel brackets (G) and brace (E). (Make sure wheels and brackets are properly oriented. See inset Figure 12). To attach the brackets, remove the nuts from the bolts and insert the bolts through the holes in the bottom of the two legs and into the holes in brace (E). Thread the nuts back on the bolts and tighten. Assemble the stand as shown in Fig. 11, using 16 M8x1.25x20mm carriage head bolts, 3/8 inch flat washers and M8x1.25 hex nuts. Align the holes in the stand legs (F) with the holes in the brackets. Insert the carriage head bolt through the hole in the leg and the hole in the bracket, place a flat washer on the carriage head bolt and thread a hex nut onto the carriage head bolt. Repeat this process for the 15 remaining holes in the legs and brackets.

NOTE: Loosely tighten the hardware for further adjustment.

Letters are on the stand brackets to ease assembly: A - Top front and rear brackets

B - Top side brackets C - Bottom side brackets

D - Bottom front and rear brackets E - Bottom brace

NOTE: Each rubber foot is provided with holes for mounting the stand to the floor surface if required.

B

A

F

C

H

D

G

E

Fig. 11

Wheel

Fig. 12

SAW TO STAND

1.Turn saw table face down on a piece of cardboard to protect the table surface. Place stand upside down onto saw and align the four holes in the stand with the mounting holes in the saw.

2.Place a 3/8 inch flat washer on a M8x1.25x45mm hex head screw. Insert the hex head screw through the mounting hole in the saw and the mounting hole in the stand. Place another 3/8 inch flat washer on the hex head screw and thread a M8x1.25 hex nut on the screw and loosely tighten. Complete this process for the other three holes.

3.Stand the saw upright, as shown in Fig. 13 (Saw is shown fully assembled here).

4.Push down on top of the saw so that the legs of the stand adjust to the surface of the floor. Tighten all hardware securely.

Fig. 13

11

Image 11

Contents BDTS200 10 Inch 254MM Table SAW Table of Contents California Proposition Safety Guidelines DefinitionsImportant Safety Instructions General Safety RulesAdditional Specific Safety Rules Grounding Instructions Power ConnectionsFunctional Description Carton ContentsParts Base AssemblyAssembly Tools Required Elevating and Supporting Surfaces for a SAW with no StandMiter Gauge Attaching Miter Gauge HolderSAW to Stand Assembling StandAttaching Blade Guard and Splitter Assembly Attaching Blade Height Adjusting HandwheelOn the screw L Fig Assembling RIP Fence Moving the SAW Locking Switch in the OFF PositionBlade Height Adjustment OperationTo Adjust Positive Stop AT 45 Degrees Blade Tilt Adjustment45 Degree Positive Stop Adjustments To Adjust Positive Stop AT 90 DegreesTable Insert Adjustment RIP Fence Operation AdjustmentsAdjusting Blade Parallel to Miter Gauge Slots Miter Gauge Operation AdjustmentsCROSS-CUTTING Changing the BladeRipping Guard Removed for CLARITY. Always USE the Guard Using Auxiliary Wood Facing on RIP FenceAccessory Dado Cutterhead Page Constructing a Push Stick Notchtohelp Preventhand FromslippingConstructing a Featherboard WHAT’S WRONG? What to DO… TroubleshootingWarranty MaintenanceAccessories ServiceScie Circulaire À Table DE 254 MM 10 PO BDTS200 Conserver CES Directives Lignes Directrices EN Matière DE Sécurité DéfinitionsProposition 65 DE LA Californie Directives DE Sécurité Importantes Règles Générales DE SécuritéConserver CES Directives Règles DE Sécurité Spécifiques SupplémentairesDirectives DE Mise À LA Terre Connexions ÉlectriquesIntroduction Description FonctionnelleContenu DU Carton Rallonges ÉlectriquesSurfaces DE Levage ET DE Support Pour UNE Scie Sans Socle AssemblageOutils Nécessaires Pour L’ASSEMBLAGE Assemblage DE LA Scie SUR Socle Fixation DU PORTE-JAUGE À OngletJauge À Onglet Assemblage DU SocleDémarrage ET Arrêt DE LA Scie Déplacement DE LA ScieFonctionnement Assemblage DU Guide LongitudinalUtilisation ET Réglages DU Guide Longitudinal Réglage DE LA Hauteur DE LA LameRéglage DE L’INCLINAISON DE LA Lame Réglages DES Butées Fixes À 90 ET 45 DegrésTronçonnage Utilisation ET Réglages DE LA Jauge À OngletChangement DE LA Lame Toujours Utiliser LE Dispositif DE Protection Sciage EN Long« Fabrication DUN Poussoir » Fraise Accessoire À RainurerFabrication D’UNE Planche EN Éventail DépannageEntretien Accessoires Sierra DE Banco BDTS200 Proposición DE California Pautas DE SEGURIDAD/DEFINICIONESInstrucciones Importantes Sobre Seguridad Normas Generales DE SeguridadGuarde Estas Instrucciones Reglas DE Seguridad Adicionales Para Sierra DE MesaInstrucciones DE Conexión a Tierra Conexiones a LA Fuente DE AlimentaciónCordón DE Extensión DE Calibre Mínimo Instrucciones DE FuncionamientoContenido DE Carton Cordones DE ExtensiónMinimo EnsamblajeHerramientas DE Ensamblaje Requeridas Sierra QUE Ensambla Ensamblado DEL Portador DE LA Escuadra DE IngletesEscuadra DE Ingletes Montaje DE LA Base DE SoporteEnsamblado DE LA Guia DE Corte a LO Largo Ensamblado DEL Volante DE Inclinacion Y Elevado DE HojaEnsamblado DEL Ensamblaje DE Protector DE Hoya Y Hendidor Operación Funcionamiento Y Ajustes DE LA Escuadra DE Ingletes Funcionamiento Y Ajustes DE LA Guia DE Corte a LO LargoAjuste DEL Inserto Para Mesa Realización DE Cortes AL Hilo Cambio DE LA HojaRealización DE Cortes Transversales UN Palo DE Empujar Fresa DE Ranurar AccesoriaConstrucción DE UNA Tabla DE Canto Biselado Construcción DE UN Palo DE EmpujarMantenimiento Detección DE ProblemasPara Otras Localidades Llame AL 55 5326 RéparationPage