Black & Decker 90528116, BDTS200 Operation, Moving the SAW, Starting and Stopping SAW

Page 15

MOVING THE SAW

To move the saw, grasp the side of the table opposite of the wheels. Lift the saw so that it is slightly off the floor and pull the table to the desired location as shown.

CAUTION: Not all floors are perfectly smooth, check both wheels each time you move the saw to ensure that they are not engaging the floor when the saw is at rest. Make sure all bolts are securely fastened.

OPERATION

OPERATIONAL CONTROLS AND ADJUSTMENTS

STARTING AND STOPPING SAW

The on/off switch (A) Fig. 29 is located on the front of the saw cabinet. To turn the saw “ON”, move the switch (A) up to the “ON” position. To turn the saw “OFF”, move the switch (A) down to the “OFF” position.

WARNING: Make sure that the switch is in the “OFF” position before plugging in the power cord. In the event of a power failure, move the switch to the “OFF” position. An accidental start-up can cause injury.

LOCKING SWITCH IN THE “OFF” POSITION

IMPORTANT: When the tool is not in use, the switch should be locked in the “OFF” position to prevent unauthorized use. To lock the tool, grasp the switch toggle (B) and pull it out of the switch (Fig. 30). With the switch toggle (B) removed, the switch will not operate. However, should the switch toggle be removed while the saw is running, the machine can be turned “OFF,” but cannot be restarted without re-inserting the switch toggle (B).

A

B

Fig. 29

Fig. 30

BLADE HEIGHT ADJUSTMENT

To adjust the height of the saw blade, turn the handwheel (A) Fig. 31. Turning the handwheel clockwise lowers the blade and turning the handwheel counter-clockwise raises the blade.

A

Fig. 31

15

Image 15
Contents BDTS200 10 Inch 254MM Table SAW Table of Contents California Proposition Safety Guidelines DefinitionsImportant Safety Instructions General Safety RulesAdditional Specific Safety Rules Grounding Instructions Power ConnectionsFunctional Description Carton ContentsParts Base AssemblyAssembly Tools Required Elevating and Supporting Surfaces for a SAW with no StandMiter Gauge Attaching Miter Gauge HolderSAW to Stand Assembling Stand Attaching Blade Guard and Splitter Assembly Attaching Blade Height Adjusting HandwheelOn the screw L Fig Assembling RIP Fence Moving the SAW Locking Switch in the OFF PositionBlade Height Adjustment OperationTo Adjust Positive Stop AT 45 Degrees Blade Tilt Adjustment45 Degree Positive Stop Adjustments To Adjust Positive Stop AT 90 DegreesTable Insert Adjustment RIP Fence Operation AdjustmentsAdjusting Blade Parallel to Miter Gauge Slots Miter Gauge Operation AdjustmentsCROSS-CUTTING Changing the BladeRipping Using Auxiliary Wood Facing on RIP Fence Accessory Dado CutterheadGuard Removed for CLARITY. Always USE the Guard Page Constructing a Push Stick Notchtohelp Preventhand FromslippingConstructing a Featherboard WHAT’S WRONG? What to DO… TroubleshootingWarranty MaintenanceAccessories ServiceScie Circulaire À Table DE 254 MM 10 PO BDTS200 Lignes Directrices EN Matière DE Sécurité Définitions Proposition 65 DE LA CalifornieConserver CES Directives Directives DE Sécurité Importantes Règles Générales DE SécuritéConserver CES Directives Règles DE Sécurité Spécifiques SupplémentairesDirectives DE Mise À LA Terre Connexions ÉlectriquesIntroduction Description FonctionnelleContenu DU Carton Rallonges ÉlectriquesAssemblage Outils Nécessaires Pour L’ASSEMBLAGESurfaces DE Levage ET DE Support Pour UNE Scie Sans Socle Assemblage DE LA Scie SUR Socle Fixation DU PORTE-JAUGE À OngletJauge À Onglet Assemblage DU SocleDémarrage ET Arrêt DE LA Scie Déplacement DE LA ScieFonctionnement Assemblage DU Guide LongitudinalUtilisation ET Réglages DU Guide Longitudinal Réglage DE LA Hauteur DE LA LameRéglage DE L’INCLINAISON DE LA Lame Réglages DES Butées Fixes À 90 ET 45 DegrésUtilisation ET Réglages DE LA Jauge À Onglet Changement DE LA LameTronçonnage Toujours Utiliser LE Dispositif DE Protection Sciage EN Long« Fabrication DUN Poussoir » Fraise Accessoire À RainurerDépannage EntretienFabrication D’UNE Planche EN Éventail Accessoires Sierra DE Banco BDTS200 Proposición DE California Pautas DE SEGURIDAD/DEFINICIONESInstrucciones Importantes Sobre Seguridad Normas Generales DE SeguridadGuarde Estas Instrucciones Reglas DE Seguridad Adicionales Para Sierra DE MesaInstrucciones DE Conexión a Tierra Conexiones a LA Fuente DE AlimentaciónCordón DE Extensión DE Calibre Mínimo Instrucciones DE FuncionamientoContenido DE Carton Cordones DE ExtensiónEnsamblaje Herramientas DE Ensamblaje RequeridasMinimo Sierra QUE Ensambla Ensamblado DEL Portador DE LA Escuadra DE IngletesEscuadra DE Ingletes Montaje DE LA Base DE SoporteEnsamblado DEL Volante DE Inclinacion Y Elevado DE Hoja Ensamblado DEL Ensamblaje DE Protector DE Hoya Y HendidorEnsamblado DE LA Guia DE Corte a LO Largo Operación Funcionamiento Y Ajustes DE LA Guia DE Corte a LO Largo Ajuste DEL Inserto Para MesaFuncionamiento Y Ajustes DE LA Escuadra DE Ingletes Cambio DE LA Hoja Realización DE Cortes TransversalesRealización DE Cortes AL Hilo UN Palo DE Empujar Fresa DE Ranurar AccesoriaConstrucción DE UNA Tabla DE Canto Biselado Construcción DE UN Palo DE EmpujarMantenimiento Detección DE ProblemasPara Otras Localidades Llame AL 55 5326 RéparationPage