Black & Decker 90528116, BDTS200 instruction manual Additional Specific Safety Rules

Page 5

ADDITIONAL SPECIFIC SAFETY RULES

WARNING: READ ALL INSTRUCTIONS BEFORE OPERATING PRODUCT. FAILURE TO FOLLOW ALL INSTRUCTIONS LISTED BELOW MAY RESULT IN ELECTRIC SHOCK, FIRE AND OR SERIOUS INJURY.

1. DO NOT OPERATE THIS MACHINE until it is assembled and installed according to the instructions.

2.OBTAIN ADVICE FROM YOUR SUPERVISOR, instructor, or another qualified person if you are not familiar with the operation of this machine.

3.FOLLOW ALL WIRING CODES and recommended electrical connections.

4.USE THE GUARDS WHENEVER POSSIBLE. Check to see that they are in place, secured, and working correctly.

5.KICKBACK IS THE NATURAL TENDENCY OF THE WORKPIECE TO BE THROWN BACK AT THE OPERATOR when the workpiece initially contacts the blade or if the workpiece pinches the blade. Kickback is dangerous and can result in serious injury.

AVOID KICKBACK by:

A.keeping blade sharp and free of rust and pitch.

B.keeping rip fence parallel to the saw blade.

C.using saw blade guard and spreader for every possible operation, including all through sawing.

D.pushing the workpiece past the saw blade prior to release.

E.never ripping a workpiece that is twisted or warped, or does not have a straight edge to guide along the fence.

F.using featherboards when the anti-kickback device cannot be used.

G.never sawing a large workpiece that cannot be controlled.

H.never using the fence as a guide when crosscutting.

I.never sawing a workpiece with loose knots or other flaws.

6.ALWAYS USE GUARDS, SPLITTER, AND ANTI-KICKBACK FINGERS whenever possible.

7.REMOVE CUT-OFF PIECES AND SCRAPS from the table before starting the saw. The vibration of the machine may cause them to move into the saw blade and be thrown out. After cutting, turn the machine off. After the blade has come to a complete stop, remove all debris.

8.NEVER START THE MACHINE with the workpiece against the blade.

9.NEVER run the workpiece between the fence and a moulding cutterhead.

10.CUTTING THE WORKPIECE WITHOUT THE USE OF A FENCE OR MITER GAUGE IS KNOWN AS “FREEHAND” CUTTING. NEVER perform “free-hand”

operations. Use either the fence or miter gauge to position and guide the workpiece.

11.HOLD THE WORKPIECE FIRMLY against the miter gauge or fence.

12.CUTTING COMPLETELY THROUGH THE WORK- PIECE IS KNOWN AS “THROUGH-SAWING”. Ripping and cross-cutting are through-sawing operations. Cutting with the grain (or down the length of the workpiece) is ripping. Cutting across the grain (or across the workpiece) is cross-cutting. Use a fence or fence system for ripping. DO NOT use a fence or fence system for cross-cutting. Instead, use a miter gauge. USE PUSH STICK(S) for ripping a narrow workpiece.

13.AVOID AWKWARD OPERATIONS AND HAND POSITIONS where a sudden slip could cause a hand to move into the blade.

14.KEEP ARMS, HANDS, AND FINGERS away from the blade.

15.NEVER have any part of your body in line with the path of the saw blade.

16.NEVER REACH AROUND or over the saw blade.

17.NEVER attempt to free a stalled saw blade without first turning the machine “OFF”.

18.PROPERLY SUPPORT LONG OR WIDE workpieces.

19.NEVER PERFORM LAYOUT, assembly or set-up work on the table/work area when the machine is running.

20.TURN THE MACHINE “OFF” AND DISCONNECT THE MACHINE from the power source before installing or removing accessories, before adjusting or changing set-ups, or when making repairs.

21.TURN THE MACHINE “OFF”, disconnect the machine from the power source, and clean the table/work area before leaving the machine. LOCK THE SWITCH IN THE “OFF” POSITION to prevent unauthorized use.

22.ADDITIONAL INFORMATION regarding the safe and proper operation of power tools (i.e. a safety video) is available from the Power Tool Institute,

1300 Sumner Avenue, Cleveland, OH 44115-2851 (www.powertoolinstitute.com). Information is also available from the National Safety Council, 1121 Spring Lake Drive, Itasca, IL 60143-3201. Please refer to the American National Standards Institute ANSI

01.1 Safety Requirements for Woodworking Machines and the U.S. Department of Labor OSHA 1910.213 Regulations.

SAVE THESE INSTRUCTIONS.

Refer to them often

and use them to instruct others.

5

Page 4 Page 6
Image 5
Page 4 Page 6
Contents BDTS200 10 Inch 254MM Table SAW Table of Contents California Proposition Safety Guidelines DefinitionsImportant Safety Instructions General Safety RulesAdditional Specific Safety Rules Grounding Instructions Power ConnectionsFunctional Description Carton ContentsParts Assembly Tools Required AssemblyElevating and Supporting Surfaces for a SAW with no Stand BaseMiter Gauge Attaching Miter Gauge HolderSAW to Stand Assembling StandAttaching Blade Guard and Splitter Assembly Attaching Blade Height Adjusting HandwheelOn the screw L Fig Assembling RIP Fence Blade Height Adjustment Locking Switch in the OFF PositionOperation Moving the SAW45 Degree Positive Stop Adjustments Blade Tilt AdjustmentTo Adjust Positive Stop AT 90 Degrees To Adjust Positive Stop AT 45 DegreesTable Insert Adjustment RIP Fence Operation AdjustmentsAdjusting Blade Parallel to Miter Gauge Slots Miter Gauge Operation AdjustmentsCROSS-CUTTING Changing the BladeRipping Guard Removed for CLARITY. Always USE the Guard Using Auxiliary Wood Facing on RIP FenceAccessory Dado Cutterhead Page Constructing a Push Stick Notchtohelp Preventhand FromslippingConstructing a Featherboard WHAT’S WRONG? What to DO… TroubleshootingAccessories MaintenanceService WarrantyScie Circulaire À Table DE 254 MM 10 PO BDTS200 Conserver CES Directives Lignes Directrices EN Matière DE Sécurité DéfinitionsProposition 65 DE LA Californie Directives DE Sécurité Importantes Règles Générales DE SécuritéConserver CES Directives Règles DE Sécurité Spécifiques SupplémentairesDirectives DE Mise À LA Terre Connexions ÉlectriquesContenu DU Carton Description FonctionnelleRallonges Électriques IntroductionSurfaces DE Levage ET DE Support Pour UNE Scie Sans Socle AssemblageOutils Nécessaires Pour L’ASSEMBLAGE Jauge À Onglet Fixation DU PORTE-JAUGE À OngletAssemblage DU Socle Assemblage DE LA Scie SUR SocleFonctionnement Déplacement DE LA ScieAssemblage DU Guide Longitudinal Démarrage ET Arrêt DE LA ScieRéglage DE L’INCLINAISON DE LA Lame Réglage DE LA Hauteur DE LA LameRéglages DES Butées Fixes À 90 ET 45 Degrés Utilisation ET Réglages DU Guide LongitudinalTronçonnage Utilisation ET Réglages DE LA Jauge À OngletChangement DE LA Lame Toujours Utiliser LE Dispositif DE Protection Sciage EN Long« Fabrication DUN Poussoir » Fraise Accessoire À RainurerFabrication D’UNE Planche EN Éventail DépannageEntretien Accessoires Sierra DE Banco BDTS200 Proposición DE California Pautas DE SEGURIDAD/DEFINICIONESInstrucciones Importantes Sobre Seguridad Normas Generales DE SeguridadGuarde Estas Instrucciones Reglas DE Seguridad Adicionales Para Sierra DE MesaInstrucciones DE Conexión a Tierra Conexiones a LA Fuente DE AlimentaciónContenido DE Carton Instrucciones DE FuncionamientoCordones DE Extensión Cordón DE Extensión DE Calibre MínimoMinimo EnsamblajeHerramientas DE Ensamblaje Requeridas Escuadra DE Ingletes Ensamblado DEL Portador DE LA Escuadra DE IngletesMontaje DE LA Base DE Soporte Sierra QUE EnsamblaEnsamblado DE LA Guia DE Corte a LO Largo Ensamblado DEL Volante DE Inclinacion Y Elevado DE HojaEnsamblado DEL Ensamblaje DE Protector DE Hoya Y Hendidor Operación Funcionamiento Y Ajustes DE LA Escuadra DE Ingletes Funcionamiento Y Ajustes DE LA Guia DE Corte a LO LargoAjuste DEL Inserto Para Mesa Realización DE Cortes AL Hilo Cambio DE LA HojaRealización DE Cortes Transversales UN Palo DE Empujar Fresa DE Ranurar AccesoriaConstrucción DE UNA Tabla DE Canto Biselado Construcción DE UN Palo DE EmpujarMantenimiento Detección DE ProblemasPara Otras Localidades Llame AL 55 5326 RéparationPage
Top Page Image Contents