Bosch Power Tools 3924-24, 3918 manual Crown Molding Angled to Table Fence

Page 69

Saw Operations

Crown Molding Angled to Table

and Fence

FIG. 31

•The advantage to cutting in this position is that no bevel setting is required. Cutting is done with 45° miter angle.

•Crown molding of up to 4-1/4” maximum width can be cut on your saw.

Follow these instructions for cutting crown molding angled to table and fence.

1. Position the molding so the bottom (part which is installed

against the wall) is against the fence. Make sure the

sliding fence is in place to provide maximum support (see

Sliding Fence for instructions).

NOTE: Crown Molding Support (accessory BB1203)

assists in holding crown molding in place during the

cutting operation. Refer to the accessory instruction

sheet for details. See page 82 for a complete accessory

list.

Sliding

Fence

Crown Molding

Support

Crown Molding

Angled Against

Fence

45º Miter

2.

Set the miter angle using the chart below. Tighten the

 

miter lock knob (Figure 31).

3.

Activate the switch. Lower the head assembly and make

 

your cut.

4.Wait until blade comes to a complete stop before returning head assembly to the raised position and/or removing workpiece.

5.ALWAYS TAKE A TEST CUT USING SCRAP TO CONFIRM CORRECT ANGLES.

Chart 2: Crown Molding Angled to Table and Fence

69

Page 68 Page 70
Image 69
Page 68 Page 70
Contents 3918 3924-24 General Safety Rules For Benchtop Tools SafetyService Safety Rules for Miter SawsSafety Safety Battery Care Battery/ChargerBattery Disposal Nickel-Cadmium BatteriesTable of Contents 20a Getting To Know Your Miter SawBevel Lock Handle Accessory Extension/Stop Holes Bevel Detent Pin Crown Molding SettingOr 24 V Battery Pack Miter Lock KnobPour les outils d’établi SécuritéRéparation Consignes de sécurité pour les scies à ongletBlessures Sécurité Entretien des piles Chargeur de pileMise au rebut des piles Piles nickel-cadmiumFrein électrique Table des matièresDescription fonctionnelle et spécifications Utilisation de l’échelle graduée d’onglet et deFamiliarisez-vous avec votre scie à onglet Bouton de blocage d’onglet Trous pour l’accessoire rallonge/butée13. Gâchette de cran d’arrêt d’onglet 14. Échelle graduée d’ongletArea de trabajo SeguridadSeguridad eléctrica Seguridad personalServicio Para cortar ingletesAserrado, amolado y taladrado AdvertenciaPersonales graves Cuidado de las baterías Batería/cargadorEliminación de las baterías Baterias de niquel-cadmioFreno eléctrico IndiceDescripción funcional y especificaciones PáginaFamiliarización con la sierra para cortar ingletes Tope de bisel de 33.9 molduras de techo Pomo de fijación de ingleteDeflector de virutas Gatillo del retén de inglete Escala de ingletesTools Needed For Assembly And Alignment AssemblyAssemblage Outils nécessaires à l’assemblage et à l’alignementHerramientas necesarias para el ensamblaje y la alineación EnsamblajeInstallation of Miter Lock Knob Unpacking and Checking ContentsOuverture de l’emballage et Vérification du contenu AssemblageEnsamblajeDesempaquetado y comprobación Del contenido Instalación del pomo de fijación De ingleteCutting Kerf Insert Removal and Installation BladePose et dépose de la lame Instalación y remoción de la hojaMoins que 10 po de diamètre et arbre de 5/8 po Assembling Dust Bag Bois traité chimiquement sous Ensamblaje de la bolsa para polvoBlade Alignment Blade Square to TableLame d’équerre par rapport La table RéglagesAjustesHoja en ángulo recto con La mesa Alignement de la lame àIf the blade is not 45 with the table, adjust 45 bevel stop AdjustmentsHoja a 45 respecto a la mesa Lame à 45 par rapport La tableGlissière à la Abaissez la tête. Bloquez en place Baje el ensamblaje del cabezal. Fíjelo en su sitioHead assembly should remain in lowered position Blade Square to FenceFence Alignment Alignement du guide Hoja en ángulo recto con el tope-guíaAlineación del tope-guía Apriete los tornillos de casquete hexagonales40-1/2 Exactement40-1/4 40-3/4IndicadorVernierde Miteringlete ScaleUso de la escala Vernier y la escala de ingletes Miter Scale Vernier Indicator Adjustment Crown Molding Detent Adjustment BevelCrown Molding Detent Adjustment Couronne biseau Graduée d’onglet VernierAjuste del indicador Vernier de la Escala de ingletes Ajuste del retén para moldura de Techo biselBe careful not to over drive nail or over InstallationInstallationTorque the bolt. This could crack foot or Damage baseEsto podría agrietar el pie o dañar la base InstalaciónPortable Mounting Using Clamps InstallationPortable Mounting Using 1x4’s Mounting ApplicationsInstallationInstalación Applications de montageAplicaciones de montaje Body and Hand Position Following instructions A, B, C, & DRaise automatically as you cut Operaciones básicas de La sierra Opérations de base de la SciePosition du corps et des mains Posición del cuerpo y de las manosWorkpiece Support Basic Saw OperationsClamps Long Workpiece SupportSoporte de la pieza de trabajo Support de l’ouvrageSwitch Activation Activación del interruptor Actionnement par interrupteurSliding Base/Fence Extension Detent OverrideCourt-circuitage du cran d’arrêt Sobrecontrol del reténExtensión de la base/tope-guía Deslizante Miter Cut Saw OperationsOperaciones de la sierra Opérations de la scieCoupe à l’onglet Corte a ingleteFollow these instructions for making your bevel cut Bevel CutCoupe en biseau Corte en biselSiga estas instrucciones para hacer un corte en bisel Follow these instructions for making your compound cut Compound CutsCortes compuestos Coupes composéesSuivez ces instructions pour pratiquer votre coupe composée Siga estas instrucciones para hacer un corte compuestoBase Molding Base molding can be cut vertical against fence or flat onCorner of wall Le guide ou à plat sur la table Coupe de moulures de base Moulures de baseMoldura de base Corte de moldura de techo Cutting Crown MoldingFollow these instructions for cutting crown molding Crown Molding Laying Flat on TableMoulures en couronne reposant à plat sur la table 33,9Serre-joint DouvrageOnglet de 31,6 Maximo 41⁄4 Moldura de techo colocada horizontalmente sobre la mesaCrown Molding Angled to Table Fence Par rapport à la table et au guide Moulure en couronne à angleLa mesa y al tope-guía Cutting Bowed Material Special CutsCutting Round or Irregularly Shaped Material Cutting thin wide MaterialCortes especiales Coupes spécialesImportant Charging Notes Remarques importantes Concernant la charge Notas importantes para cargarCharging Battery Pack Hour Charger Indicators, symbols MeaningIndicadores, símbolos y significado Carga del paquete de baterias Cargador de 1 horaTotalmente cargado Charging Battery Pack Minute Single Bay-BC130 Con el paquete de baterías Charge rapideCharging Battery Pack Minute Dual Bay-BC230 Maintien Deux baies BC230Accessoires AccessoriesExtension Cords RallongesAccesorios Cordóns de extensiónMotor Brush Replacement BatteriesCarbon Brushes Mantenimiento y Lubricación Remplacement des balais De moteurCare of Blades CleaningTool Lubrication BearingsCuidado de las hojas LimpiezaLubricación de las herramientas CojinetesDuide de Dépannage Troubleshooting GuideGenerales EléctricasClean head assembly Properly after servicePart failure Pivot spring or guard spring not replacedPuntos de pivote sueltos Use protección para los ojosFallo de pieza Ajustes y reparacionesLimited Warranty of Bosch Portable and Benchtop Power Tools

3924-24, 3918 specifications

Bosch Power Tools has long been a leader in innovation and quality within the power tool industry, and its models 3918 and 3924-24 are prime examples of their commitment to performance and reliability. These tools are designed for both professionals and DIY enthusiasts, providing efficient solutions for a variety of tasks.

The Bosch 3918 is primarily a reciprocating saw that features a robust 6.5-amp motor, delivering impressive power for cutting through wood, metal, and other materials. One of its standout features is the tool-less blade change system, which allows users to switch blades quickly and easily without needing additional tools. This is not only time-saving but also enhances the user experience by minimizing downtime between cuts.

The saw also boasts a variable speed dial that can reach up to 2,700 strokes per minute, giving users optimal control over their cutting tasks. The pivoting shoe provides increased stability and allows for precise cuts in various applications. Additionally, the saw includes an electronic motor protection system, which helps prevent overheating and extends the lifespan of the tool.

On the other hand, the Bosch 3924-24 is a powerful angle grinder. With a 6.0-amp motor, it delivers high performance while being compact and lightweight. The grinder comes with a soft grip handle, making it comfortable for extended use. Its one-touch guard allows users to adjust the guard without any tools, thus enhancing convenience during operations.

This model is equipped with a direct-drive motor that increases torque and ensures that it works efficiently under load. The 3924-24's efficient dust management system minimizes dust and debris, providing a cleaner workspace and improving visibility during operations. Additionally, the grinder features a two-position side handle for added control and stability, making it suitable for a variety of grinding, cutting, and polishing applications.

Both Bosch Power Tools models, 3918 and 3924-24, exemplify the brand's commitment to quality, safety, and user ergonomics. Their advanced features, robust construction, and innovative technologies make them indispensable tools for any serious craftsman or home improvement enthusiast. Bosch continues to enhance its tools with practical features that reflect the needs of its users, ensuring that professionals get the results they demand while maintaining ease of use.
Top Page Image Contents