Cisco Systems NME-WAE Service-module integrated-service-engine default-boot, None Privileged Exec

Page 17

service-module integrated-service-engine default-boot

service-module integrated-service-engine default-boot

To configure the integrated-service-engine (ISE) network module to use the default BIOS and bootloader, use the service-moduleintegrated-service-enginedefault-bootcommand in privileged EXEC mode.

service-module integrated-service-engine slot/unit default-boot

Syntax Description	slot	Slot number of the network module in the router chassis.
	unit	Number of the daughter card on the network module. For ISE network
		modules, always use 0.

Defaults

Command Modes

Command History

None

Privileged EXEC

ReleaseModification

12.4(9)T	This command was introduced for the ISE network module.

Examples	After a downtime event or failed upgrade, use the service-moduleintegrated-service-engineslot/unit
	default-bootcommand to configure the network module to use the primary BIOS and primary
	bootloader to perform startup routines.
	The following is sample output from the integrated-service-engineslot/unit default-bootcommand for
	a port adapter in chassis slot 2 on a Cisco router:
	Router# service-module integrated-service-engine 2/0 default-boot
	clear	Clear Default Boot
	set	Set Default Boot

Router# service-module integrated-service-engine 2/0 default-boot clear

Router# service-module integrated-service-engine 2/0 default-boot set

Configuring Cisco Access Routers and the NME-WAE Network Module for ACNS Deployments

	OL-13140-02	17

Image 17

Contents Contents Restrictions for Cisco WAE Network Modules Prerequisites for Installing the Cisco WAE Network ModulesCisco WAE Network Module Hardware Description Hard Disk and Memory SpecificationsFaceplate and LEDs Model Hard Disk MemoryCF card ShutdownOn This Hardware Interface Configure These Settings Using ThisHardware Interfaces This section contains the following topicsSummary Steps Detailed Steps Examples Setting Up Network Module InterfacesExample Procedure CommandDisplay the router running configuration so that you can Save the router running configurationVerify interface configurations Opening and Closing a Network Module SessionPress Control-Shift-6 Press Ctrl-Shift-6 Example ConfigurationShutting Down and Starting Up Cisco WAE Network Modules Accessing the Acns Software on the Network ModuleConfiguration Mode Command Purpose Displaying Status and Diagnostic Output Command Purpose Cisco technical support for problem Service module. This information is useful toDisplays general information about DiagnosisCommand Reference Interface integrated-service-engine slot/unit Interface integrated-service-engineSyntax Description Defaults Command Modes Command History ReleaseModificationDefaults Command Modes Command History Service-module integrated-service-engine default-bootBootloader to perform startup routines None Privileged ExecService-module integrated-service-engine slot/unit reload Service-module integrated-service-engine reloadCommand Description Usage GuidelinesService-module integrated-service-engine slot/unit reset Service-module integrated-service-engine resetRelated Commands Description Router# service-module integrated-service-engine 1/0 resetCommand Description Username Service-module integrated-service-engine sessionOpen Related Commands Description Service-module integrated-service-engine slot/unit shutdown Service-module integrated-service-engine shutdownInterface integrated-service-engine Integrated-service-engine resetCommand Description Access router Service-module integrated-service-engine statisticsService-module integrated-service-engine slot/unit status Service-module integrated-service-engine statusRouter# service-module integrated-service-engine 1/0 status Display the ISE network module software release versionRelated Commands Description Field Description Show controllers integrated-service-engineShow controllers integrated-service-engine slot/unit Related Commands Description Release Modification Show diagShow diag slot Show diag subslot Field Descriptions Network modules Displays basic interface configuration information forIntegrated-service-engine network modules Command Modes Command History Show interfaces integrated-service-engineShow interfaces integrated-service-engine slot/unit Field Description Station that is transmitting bad data Errors created when the CRC generated by the originating LANField Description Bootloader BoothelperGlossary BladeRelated Documentation Service or servicesEngine Syslog Related Topic Document TitlePage OL-13140-02