Cisco Systems Guide to Cisco Integrated Service Engine Reboot and Graceful Shutdown Procedures

Page 19

service-module integrated-service-engine reset

service-module integrated-service-engine reset

To reset the integrated-service-engine (ISE) network module hardware, use the service-moduleintegrated-service-engine reset command in privileged EXEC mode.

service-module integrated-service-engine slot/unit reset

Syntax Description	slot	Slot number of the network module in the router chassis.
	/unit	Number of the daughter card on the network module. For ISE network
		modules, always use 0. The slash mark (/) is required between the slot
		argument and the unit argument.

Defaults

Command Modes

Command History

None

Privileged EXEC

ReleaseModification

12.4(9)T	This command was introduced for ISE network modules.

Usage Guidelines

Caution

Examples

At the confirmation prompt, press Enter to confirm the action or n to cancel.

Because you may lose data, use the service-moduleintegrated-service-engine reset command only to recover from a shutdown or failed state.

The following example resets the hardware on the ISE network module in slot 1:

Router# service-module integrated-service-engine 1/0 reset

Use reset only to recover from shutdown or failed state

Warning: May lose data on the hard disk!

Do you want to reset?[confirm]

Related Commands		Command	Description
		interface integrated-service-engine	Configures an interface for ISE network modules and enters
			interface configuration mode.

		service-module	Performs a graceful shutdown and reboot on the ISE network
		integrated-service-engine reload	module ACNS operating system.

		service-module	Gracefully shuts down ISE network modules.
		integrated-service-engine
		shutdown

		Configuring Cisco Access Routers and the NME-WAE Network Module for ACNS Deployments


	OL-13140-02				19
	OL-13140-02				19

Image 19

Contents Contents Restrictions for Cisco WAE Network Modules Prerequisites for Installing the Cisco WAE Network ModulesModel Hard Disk Memory Hard Disk and Memory SpecificationsCisco WAE Network Module Hardware Description Faceplate and LEDsCF card ShutdownThis section contains the following topics Using ThisOn This Hardware Interface Configure These Settings Hardware InterfacesSummary Steps Detailed Steps Examples Setting Up Network Module InterfacesExample Procedure CommandOpening and Closing a Network Module Session Save the router running configurationDisplay the router running configuration so that you can Verify interface configurationsPress Control-Shift-6 Press Ctrl-Shift-6 Example ConfigurationConfiguration Mode Command Purpose Accessing the Acns Software on the Network ModuleShutting Down and Starting Up Cisco WAE Network Modules Displaying Status and Diagnostic Output Command Purpose Diagnosis Service module. This information is useful toCisco technical support for problem Displays general information aboutCommand Reference ReleaseModification Interface integrated-service-engineInterface integrated-service-engine slot/unit Syntax Description Defaults Command Modes Command HistoryNone Privileged Exec Service-module integrated-service-engine default-bootDefaults Command Modes Command History Bootloader to perform startup routinesUsage Guidelines Service-module integrated-service-engine reloadService-module integrated-service-engine slot/unit reload Command DescriptionRouter# service-module integrated-service-engine 1/0 reset Service-module integrated-service-engine resetService-module integrated-service-engine slot/unit reset Related Commands DescriptionCommand Description Open Service-module integrated-service-engine sessionUsername Related Commands Description Integrated-service-engine reset Service-module integrated-service-engine shutdownService-module integrated-service-engine slot/unit shutdown Interface integrated-service-engineCommand Description Access router Service-module integrated-service-engine statisticsDisplay the ISE network module software release version Service-module integrated-service-engine statusService-module integrated-service-engine slot/unit status Router# service-module integrated-service-engine 1/0 statusRelated Commands Description Show controllers integrated-service-engine slot/unit Show controllers integrated-service-engineField Description Related Commands Description Show diag slot Show diagRelease Modification Show diag subslot Field Descriptions Integrated-service-engine network modules Displays basic interface configuration information forNetwork modules Show interfaces integrated-service-engine slot/unit Show interfaces integrated-service-engineCommand Modes Command History Field Description Station that is transmitting bad data Errors created when the CRC generated by the originating LANField Description Blade BoothelperBootloader GlossaryRelated Topic Document Title Service or servicesRelated Documentation Engine SyslogPage OL-13140-02