Cisco Systems NME-WAE manual Glossary, Blade, Boothelper, Bootloader, Network module

Page 37

Glossary

 

 

Table 6

show interfaces integrated-service-engine Field Descriptions (continued)

 

 

 

 

 

 

 

Field

 

Description

 

 

 

 

 

 

 

deferred

 

Indicates that the chip, while ready to transmit a frame, had to

 

 

 

 

defer because the carrier was asserted.

 

 

 

 

 

 

 

lost carrier

 

Number of times that the carrier was lost during transmission.

 

 

 

 

 

 

 

no carrier

 

Number of times that the carrier was not present during the

 

 

 

 

transmission.

 

 

 

 

 

 

output buffer failures,

Number of failed buffers and number of buffers swapped out.

 

 

output buffers swapped out

 

 

 

 

 

 

 

 

 

 

 

Related Commands

 

Command

 

Description

 

 

 

 

 

interface integrated-service-engineConfigures an interface for an ISE and enters interface

 

 

 

 

configuration mode.

 

 

 

 

 

 

 

show diag

 

Displays controller information for ISE network modules.

 

 

 

 

 

Glossary

ACNS

Application and Content Networking System software.

ARP

Address Resolution Protocol. Internet protocol used to map an IP address to

 

a MAC address.

blade

Alternate term for service module.

boothelper

A small subset of the system software that runs on the module. It boots the

 

module from the network and assists in software installation and upgrades,

 

disaster recovery, and other operations when the module cannot access its

 

software.

bootloader

A small set of system software that runs when the system first powers up. It

 

loads the operating system (from the disk, network, or compactFlash), which

 

loads and runs the Cisco Application and Content Networking System

 

application. The bootloader may optionally load and run the boothelper.

FTP

File Transfer Protocol. Application protocol, part of the TCP/IP protocol

 

stack, used for transferring files between network nodes.

ISE

Integrated Service Engine. The network module is referred to as the

 

integrated service engine (ISE) on the IOS CLI.

network module

Standalone content engine with its own startup and run-time configurations

 

that are independent of the IOS configuration on the router.

NME

See network module,

Configuring Cisco Access Routers and the NME-WAE Network Module for ACNS Deployments

 

OL-13140-02

37

 

 

 

Image 37
Contents Contents Restrictions for Cisco WAE Network Modules Prerequisites for Installing the Cisco WAE Network ModulesCisco WAE Network Module Hardware Description Hard Disk and Memory SpecificationsFaceplate and LEDs Model Hard Disk MemoryCF card ShutdownOn This Hardware Interface Configure These Settings Using ThisHardware Interfaces This section contains the following topicsSummary Steps Detailed Steps Examples Setting Up Network Module InterfacesExample Procedure CommandDisplay the router running configuration so that you can Save the router running configurationVerify interface configurations Opening and Closing a Network Module SessionPress Control-Shift-6 Press Ctrl-Shift-6 Example ConfigurationConfiguration Mode Command Purpose Accessing the Acns Software on the Network ModuleShutting Down and Starting Up Cisco WAE Network Modules Displaying Status and Diagnostic Output Command Purpose Cisco technical support for problem Service module. This information is useful toDisplays general information about DiagnosisCommand Reference Interface integrated-service-engine slot/unit Interface integrated-service-engineSyntax Description Defaults Command Modes Command History ReleaseModificationDefaults Command Modes Command History Service-module integrated-service-engine default-bootBootloader to perform startup routines None Privileged ExecService-module integrated-service-engine slot/unit reload Service-module integrated-service-engine reloadCommand Description Usage GuidelinesService-module integrated-service-engine slot/unit reset Service-module integrated-service-engine resetRelated Commands Description Router# service-module integrated-service-engine 1/0 resetCommand Description Open Service-module integrated-service-engine sessionUsername Related Commands Description Service-module integrated-service-engine slot/unit shutdown Service-module integrated-service-engine shutdownInterface integrated-service-engine Integrated-service-engine resetCommand Description Access router Service-module integrated-service-engine statisticsService-module integrated-service-engine slot/unit status Service-module integrated-service-engine statusRouter# service-module integrated-service-engine 1/0 status Display the ISE network module software release versionRelated Commands Description Show controllers integrated-service-engine slot/unit Show controllers integrated-service-engineField Description Related Commands Description Show diag slot Show diagRelease Modification Show diag subslot Field Descriptions Integrated-service-engine network modules Displays basic interface configuration information forNetwork modules Show interfaces integrated-service-engine slot/unit Show interfaces integrated-service-engineCommand Modes Command History Field Description Station that is transmitting bad data Errors created when the CRC generated by the originating LANField Description Bootloader BoothelperGlossary BladeRelated Documentation Service or servicesEngine Syslog Related Topic Document TitlePage OL-13140-02