Cisco Systems NME-WAE Hardware Interfaces, Using This, This section contains the following topics

Page 5

Setting Up Cisco WAE Network Modules and Opening a Session

Hardware Interfaces

The host router and network module use several interfaces for internal and external communication (see Figure 2). Each interface is configurable by using a IOS-like CLI.

Figure 2

Router and Network Module Interface

Host Router (Top View)

2Router interface to module

3Module interface to router

 

 

 

Network Module

 

 

 

 

 

4 Module interface to external link

1 Router interface to external link

231229

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Using This

 

On This Hardware Interface...

Configure These Settings...

Configuration Interface

 

 

 

 

1

Router interface to external link

Standard router settings

Router IOS

 

(GigabitEthernet slot/0)

 

command-line interface

 

 

 

 

2

Router interface to module

Module IP address and default

 

 

(Integrated-Service-Engine slot/0)

gateway router

 

 

 

 

 

3

Module interface to router

All other module and ACNS

NME-WAE network

 

(Integrated-Service-Engine slot/0)

application settings

module command-line

 

 

 

interface

4

Module interface to external link

All other module and ACNS

 

 

(Integrated-Service-Engine slot/0)

application settings

 

 

 

 

 

The NME-WAE accepts traffic to be optimized on either its internal or external interface but not on both interfaces. Configure either the module internal interface to the router (see callout 3 in Figure 2) or the module external interface (see callout 4 in Figure 2) but not both interfaces.

When using the ACNS Content Distribution Manager GUI for an NME-WAE device, the internal interface to the router is designated as slot 1, port 0 and the external network interface is designated as slot 2, port 0, regardless of the physical slot in which the NME-WAE is installed.

Setting Up Cisco WAE Network Modules and Opening a Session

This section contains the following topics:

•Setting Up Network Module Interfaces, page 6

•Opening and Closing a Network Module Session, page 8

Configuring Cisco Access Routers and the NME-WAE Network Module for ACNS Deployments

 

OL-13140-02

5

 

 

 

Page 4 Page 6
Image 5
Page 4 Page 6
Contents Contents Restrictions for Cisco WAE Network Modules Prerequisites for Installing the Cisco WAE Network ModulesCisco WAE Network Module Hardware Description Hard Disk and Memory SpecificationsFaceplate and LEDs Model Hard Disk MemoryCF card ShutdownOn This Hardware Interface Configure These Settings Using ThisHardware Interfaces This section contains the following topicsSummary Steps Detailed Steps Examples Setting Up Network Module InterfacesExample Procedure CommandDisplay the router running configuration so that you can Save the router running configurationVerify interface configurations Opening and Closing a Network Module SessionPress Control-Shift-6 Press Ctrl-Shift-6 Example ConfigurationShutting Down and Starting Up Cisco WAE Network Modules Accessing the Acns Software on the Network ModuleConfiguration Mode Command Purpose Displaying Status and Diagnostic Output Command Purpose Cisco technical support for problem Service module. This information is useful toDisplays general information about DiagnosisCommand Reference Interface integrated-service-engine slot/unit Interface integrated-service-engineSyntax Description Defaults Command Modes Command History ReleaseModificationDefaults Command Modes Command History Service-module integrated-service-engine default-bootBootloader to perform startup routines None Privileged ExecService-module integrated-service-engine slot/unit reload Service-module integrated-service-engine reloadCommand Description Usage GuidelinesService-module integrated-service-engine slot/unit reset Service-module integrated-service-engine resetRelated Commands Description Router# service-module integrated-service-engine 1/0 resetCommand Description Username Service-module integrated-service-engine sessionOpen Related Commands Description Service-module integrated-service-engine slot/unit shutdown Service-module integrated-service-engine shutdownInterface integrated-service-engine Integrated-service-engine resetCommand Description Access router Service-module integrated-service-engine statisticsService-module integrated-service-engine slot/unit status Service-module integrated-service-engine statusRouter# service-module integrated-service-engine 1/0 status Display the ISE network module software release versionRelated Commands Description Field Description Show controllers integrated-service-engineShow controllers integrated-service-engine slot/unit Related Commands Description Release Modification Show diagShow diag slot Show diag subslot Field Descriptions Network modules Displays basic interface configuration information forIntegrated-service-engine network modules Command Modes Command History Show interfaces integrated-service-engineShow interfaces integrated-service-engine slot/unit Field Description Station that is transmitting bad data Errors created when the CRC generated by the originating LANField Description Bootloader BoothelperGlossary BladeRelated Documentation Service or servicesEngine Syslog Related Topic Document TitlePage OL-13140-02
Top Page Image Contents