Appendix A : Parameter List
This section includes the
The Configuration File
The table shows the parameter list stored in the config.ini file. The middle column states the default values, where applicable. The
Parameter name |
| Value | Description |
|
|
|
|
[Server] |
|
|
|
HardwareAddress | = | 00:40:8c:11:00:86 | The |
|
|
| a Locally Administrated Address. The value shown is an example only. |
Date | = | ||
Time | = | 12:00:00 | hh:mm:ss, enter the time followed by ! to set manually |
FactoryDefaults | = | no | Set to yes to restore factory default settings. |
Restart | = | no | Set to yes to restart the |
TimeZone | = | UTC | Must be set to the time zone that the |
|
|
| “TimeZone Parameter Values” on page 42. |
TimeSyncSource | = | NDS | Specifies the time source for the |
|
|
| network. Set to NTP for UNIX and SMB over TCP/IP. |
ServerPassword | = | pass | The Supervisor, Administrator or Root user password used for basically all |
|
|
| protocols; i.e. HTTP, NetWare bindery, SMB user level, SNMP and FTP. Once |
|
|
| written into the configuration file, the password will not be shown but replaced |
|
|
| with *’s, representing each letter of the password. |
Cache | = | mirror | Specifies the caching level: none, normal, mirror, persistent |
Flush Cache | = | no | Set to yes to remove all information from the hard disk. |
|
|
|
|
[SCSI] |
|
|
|
SCSITermination | = | on | Always on. |
JukeBoxLockTime | = | 0 | Specifies the maximum duration for a data read operation during multiple |
|
|
| access requests to prevent disc changer fluttering. Default is 0 seconds |
|
|
| which disables the function. |
DisconnectReselect | = | on | Set to off to disable the disconnect/reselect function in the disc drives. |
BusMode | = | Asynchronous | Specifies the transfer mode on the SCSI bus: Asynchronous, Synchronous, |
|
|
| |
|
|
|
|
[IP] |
|
|
|
InternetAddress | = | 192.36.253.80 | The |
DefaultRouter | = | 0.0.0.0 | The IP address for the default router. All traffic directed outside the local |
|
|
| network (according to the NetMask) is sent to the default router. Any re- |
|
|
| routing via other routers is done automatically. The default 0.0.0.0 indicates |
|
|
| that no default router is set. |
NetMask | = | 0.0.0.0 | Used to determine when the traffic should be sent via a router. For example, |
|
|
| the normal class C mask is 255.255.255.0. The default 0.0.0.0 indicates that |
|
|
| automatic router sensing is used. |
BOOTPEnable | = | yes | Enables BOOTP IP address setup. |
RARPEnable | = | yes | Enables RARP IP address setup. |
DHCPEnable | = | yes | Enables DHCP IP address setup. |
DomainName | = |
| Name of the domain to which the |
PrimaryDNS | = | 0.0.0.0 | The IP address of the primary DNS server. Used for identifying computers |
|
|
| with names instead of IP addresses. |
SecondaryDNS | = | 0.0.0.0 | The IP address of the secondary DNS server, should the primary DNS server |
|
|
| be unavailable or disconnected. |
NTPServer |
|
| Name or IP address for the NTP server. |
EnableWINS | = | no | Enables WINS over NetBIOS/TCP/IP. |
PrimaryWINSserver | = | 0.0.0.0 | The IP address of the primary WINS server. |
SecondaryWINSserver | = | 0.0.0.0 | The IP address of the secondary WINS server, if required. |
|
|
|
|
|
|
|
|
40
<DRB1239>