Cisco Systems Comprehensive Guide on Cisco Integrated Service Engine and WAE Configuration

Page 26

service-module integrated-service-engine status

service-module integrated-service-engine status

To display configuration information related to software on the integrated-service-engine (ISE) side of

anetwork module, use the service-moduleintegrated-service-engine status command in privileged EXEC mode.

service-module integrated-service-engine slot/unit status

Syntax Description	slot	Slot number of the network module in the router chassis.
	/unit	Number of the daughter card on the network module. For ISE network
		modules, always use 0. The slash mark (/) is required between the slot
		argument and the unit argument.

Defaults

Command Modes

Command History

None

Privileged EXEC

ReleaseModification

12.4(9)T	This command was introduced for ISE network modules.

Usage Guidelines	Use the service-module integrated-service-engine status command to perform the following tasks:
	• Display the ISE network module software release version
	• Check the ISE network module status (steady or down)

Examples	The following example displays information for an ISE network module that is installed in slot 1 of an
	access router:
	Router# service-module integrated-service-engine 1/0 status
	Service Module is Cisco Integrated-Service-Engine1/0
	Service Module supports session via TTY line 66
	Service Module is in Steady state
	Getting status from the Service Module, please wait..
	Cisco Application and Content Networking System Software 5.5.7 (b17 Apr 27 2007 08:56:37)
	Restarted at Sun Apr 1 15:32:38 2007
	The following example displays information for an ISE network module that is not running:
	Router# service-module integrated-service-engine 1/0 status
	Service Module is Cisco Integrated-Service-Engine1/0
	Service Module supports session via TTY line 258
	Service Module is trying to recover from reset/shutdown
	Service Module status is not available

Configuring Cisco Access Routers and the NME-WAE Network Module for ACNS Deployments

26	OL-13140-02

Image 26

Contents Contents Prerequisites for Installing the Cisco WAE Network Modules Restrictions for Cisco WAE Network ModulesFaceplate and LEDs Hard Disk and Memory SpecificationsCisco WAE Network Module Hardware Description Model Hard Disk MemoryShutdown CF cardHardware Interfaces Using ThisOn This Hardware Interface Configure These Settings This section contains the following topicsSetting Up Network Module Interfaces Summary Steps Detailed Steps ExamplesProcedure Command ExampleVerify interface configurations Save the router running configurationDisplay the router running configuration so that you can Opening and Closing a Network Module SessionPress Control-Shift-6 Example Configuration Press Ctrl-Shift-6Shutting Down and Starting Up Cisco WAE Network Modules Accessing the Acns Software on the Network ModuleConfiguration Mode Command Purpose Displaying Status and Diagnostic Output Command Purpose Displays general information about Service module. This information is useful toCisco technical support for problem DiagnosisCommand Reference Syntax Description Defaults Command Modes Command History Interface integrated-service-engineInterface integrated-service-engine slot/unit ReleaseModificationBootloader to perform startup routines Service-module integrated-service-engine default-bootDefaults Command Modes Command History None Privileged ExecCommand Description Service-module integrated-service-engine reloadService-module integrated-service-engine slot/unit reload Usage GuidelinesRelated Commands Description Service-module integrated-service-engine resetService-module integrated-service-engine slot/unit reset Router# service-module integrated-service-engine 1/0 resetCommand Description Username Service-module integrated-service-engine sessionOpen Related Commands Description Interface integrated-service-engine Service-module integrated-service-engine shutdownService-module integrated-service-engine slot/unit shutdown Integrated-service-engine resetCommand Description Service-module integrated-service-engine statistics Access routerRouter# service-module integrated-service-engine 1/0 status Service-module integrated-service-engine statusService-module integrated-service-engine slot/unit status Display the ISE network module software release versionRelated Commands Description Field Description Show controllers integrated-service-engineShow controllers integrated-service-engine slot/unit Related Commands Description Release Modification Show diagShow diag slot Show diag subslot Field Descriptions Network modules Displays basic interface configuration information forIntegrated-service-engine network modules Command Modes Command History Show interfaces integrated-service-engineShow interfaces integrated-service-engine slot/unit Field Description Errors created when the CRC generated by the originating LAN Station that is transmitting bad dataField Description Glossary BoothelperBootloader BladeEngine Syslog Service or servicesRelated Documentation Related Topic Document TitlePage OL-13140-02